Logo Leibniz Universität Hannover
Logo: IW
Logo Leibniz Universität Hannover
Logo: IW
  • Zielgruppen
  • Suche
 

Publikationen von Prof. Dr.-Ing. Hans Jürgen Maier

2019

Zeitschriften/Aufsätze

Karsten, E.; Gerstein, G.; Golovko, O.; Dalinger, A.; Lauhoff, C.; Krooss, P.; Niendorf, T.; Samsonenko, A.; Maier, H. J. (2019): Tailoring the Microstructure in Polycrystalline Co–Ni–Ga High-Temperature Shape Memory Alloys by Hot Extrusion, Shap. Mem. Superelasticity 5, 2019 (1), 84-94
DOI: 10.1007/s40830-019-00208-7

Krooß, P.; Lauhoff, C.; Langenkämper, D.; Paulsen, A.; Reul, A.; Degener, S.; Aminforoughi, B.; Frenzel, J.; Somsen, C.; Schmahl, W. W.; Eggeler, G.; Maier, H. J.; Niendorf, T. (2019): Impact of Heating–Cooling Rates on the Functional Properties of Ti–20Ta–5Al High-Temperature Shape Memory Alloys, Shap. Mem. Superelasticity 5, 2019 (1), 95-105
DOI: 10.1007/s40830-019-00207-8

Schöler, S.; Schmieding, M.; Yilkiran, D.; Özkaya, F.; Nowak, C.; Möhwald, K.; Behrens, B.-A.; Maier, H. J. (2019): Wear behavior of selectively oxidized α-Fe2O3 oxide low-friction layer systems on PM tool steel surfaces, Wear 426-427, 2019, 1603-1615
DOI: 10.1016/j.wear.2019.01.009

Schwarzenböck, E.; Hack, T.; Kolb, M.; Engel, C.; Heidenblut, T.; Maier, H. J. (2019): Evolution of surface characteristics of two industrial 7xxx aluminium alloys exposed to humidity at moderate temperature, Surface and Interface Analysis 51, 2019 (19), 5775
DOI: 10.1002/sia.6652

Zeller, S.; Baldrich, M.; Gerstein, G.; Nuernberger, F.; Loehnert, S.; Maier, H. J.; Wriggers, P. (2019): Material models for the thermoplastic material behaviour of a dual-phase steel on a microscopic and a macroscopic length scale, Journal of the Mechanics and Physics of Solids 129, 2019, 205-228
DOI: 10.1016/j.jmps.2019.04.012

Panchenko, E. Y.; Timofeeva, E. E.; Chumlyakov, Y. I.; Osipovich, K. S.; Tagiltsev, A. I.; Gerstein, G.; Maier, H. J. (2019): Compressive shape memory actuation response of stress-induced martensite aged Ni51Fe18Ga27Co4 single crystals, Materials Science and Engineering: A 746, 2019, 448-455
DOI: 10.1016/j.msea.2019.01.004

Sajadifar, S. V.; Yapici, G. G.; Demler, E.; Krooß, P.; Wegener, T.; Maier, H. J.; Niendorf, T. (2019): Cyclic deformation response of ultra-fine grained titanium at elevated temperatures, International Journal of Fatigue 122, 2019, 228-239
DOI: 10.1016/j.ijfatigue.2019.01.021

Spachtholz, J.; Affeldt, E. E.; Maier, H. J.; Hammer, J. (2019): The effect of temperature gradients in thermo-mechanical fatigue testing, Materials at High Temperatures 36, 2018 (2), 97-103
DOI: 10.1080/09603409.2018.1466500

Eftifeeva, A.; Panchenko, E.; Chumlyakov, Y.; Yanushonite, E.; Gerstein, G.; Maier, H. J. (2019): Compressive response of high-strength [001]-oriented single crystals of a Co35Ni35Al30 shape memory alloy, Journal of Alloys and Compounds 787, 2019, 963-971
DOI: 10.1016/j.jallcom.2019.02.185

Patentschriften

Freytag, P.; Maier, H. J.; Rissing, L.; Klaas, D.; Wienecke, A. (2019): Konstruktionsbauteil eines technischen Gegenstands sowie Verfahren zur Herstellung des Konstruktionsbauteils, Patentschrift: DE 102015106002, 06.03.2019

2018

Konferenz

Schöler, S.; Yilkiran, D.; Wulff, D.; Özkaya, F.; Möhwald, K.; Behrens, B.-A.; Maier, H. J. (2018): Selective oxidation of tool steel surfaces under a protective gas atmosphere using inductive heat treatment, In: Vollertsen, F. et al. (Hrsg.): 5th International Conference on New Forming Technology, ICNFT 2018. Bremen, 18.09.-21.09.18. MATEC Web Conf. 190, 2018, S. 14003
DOI: 10.1051/matecconf/201819014003

Schmidt, H. C.; Homberg, W.; Orive, A. G.; Grundmeier, G.; Hordych, I.; Maier, H. J. (2018): Cold pressure welding of aluminium-steel blanks: Manufacturing process and electrochemical surface preparation, In: Fratini, L. et al. (Hrsg.): Proceedings of the 21st International ESAFORM Conference on Material Forming. ESAFORM 2018. Palermo. AIP Conference Proceedings 1960, 2018 (1), S. 50007
DOI: 10.1063/1.5034880

Hordych, I.; Rodman, D.; Nürnberger, F.; Schmidt, H. C.; Orive, A. G.; Homberg, W.; Grundmeier, G.; Maier, H. J. (2018): Influence of heat-pretreatments on the microstructural and mechanical properties of galfan-coated metal bonds, In: Fratini, L. et al. (Hrsg.): Proceedings of the 21st International ESAFORM Conference on Material Forming. ESAFORM 2018. Palermo. AIP Conference Proceedings 1960, 2018 (1), S. 40007
DOI: 10.1063/1.5034861

Nothdurft, S.; Ohrdes, H.; Twiefel, J.; Wallaschek, J.; Mildebrath, M.; Maier, H. J.; Hassel, T.; Overmeyer, L.; Kaierle, S. (2018): Influence of ultrasonic amplitude and position in the vibration distribution on the microstructure of a laser welded aluminum alloy, In: International Congress on Applications of Lasers & Electro-Optics, ICALEO 2018. Orlando, Fl. USA. 14.10.-18.10.2018

Gerstein, G.; Briukhanov, A.; Gutknecht, F.; Volchok, N.; Clausmeyer, T.; Nürnberger, F.; Tekkaya, A. E.; Maier, H. J. (2018): Evaluation of micro-damage by acoustic methods, In: 17th International Conference on Metal Forming. Metal Forming 2018. Toyohashi, Japan, 16.09. - 19.09.2018, Procedia Manufacturing 15, 2018, S. 527-534
DOI: 10.1016/j.promfg.2018.07.273

Eftifeeva A., Panchenko E., Chumlyakov Y., Gerstein G., Maier H. J. (2018): The effects of stress-induced martensite ageing on shape memory behavior in Co35Ni35Al30 single crystals, ESOMAT 2018, 11th European Symposium on Martensitic Transformations. Metz, France. 27.08. - 31.08.2018

Firstov G., Kosorukova T., Timoshevskii A., Koval Yu., Odnosum V., Matviychuk Yu., Gerstein G., Maier H. J. (2018): Strategies for high entropy shape memory alloy design - from motivation to structure and properties, ESOMAT 2018, 11th European Symposium on Martensitic Transformations. Metz, France. 27.08. - 31.08.2018

Panchenko E., Timofeeva E. E., Chumlyakov Y. I., Osipovich K. S., Larchenkova N. G., Pichkaleva M. V., Tokhmetova A. B., Gerstein G., Maier H. J. (2018): Stress-induced martensite ageing in single crystals of Ni-based Heusler alloy: processing, effect of orientation and functional properties, ESOMAT 2018, 11th European Symposium on Martensitic Transformations. Metz, France. 27.08. - 31.08.2018

Langenkämper, D.; Paulsen, A.; Somsen, C.; Frenzel, J.; Karsten, E.; Maier, H. J.; Eggeler, G. (2018): Synchrotron radiation and transmission electron microscopy investigations on the formation and dissolution temperatures of the w -phase in Ti-Ta high temperature shape memory alloys, ESOMAT 2018, 11th European Symposium on Martensitic Transformations. Metz, France. 27.08. - 31.08.2018

Krooß, P.; Lauhoff, C.; Paulsen, A.; Frenzel, J.; Somsen, C.; Langenkämper, D.; Reul, A.; Schmahl, W.; Karsten, E.; Maier, H.; Niendorf, T. (2018): Effect of the heating-cooling rate on the functional properties of Ti-Ta-Al HT-SMAs, ESOMAT 2018, 11th European Symposium on Martensitic Transformations. Metz, France. 27.08. - 31.08.2018

Timofeeva, E.; Panchenko, E.Yu.; Larchenkova, N.G.; Chumlyakov, Yu.I.; Maier, H.J. (2018): Two-way shape memory effect in [001]-oriented Ni49Fe18Ga27Co6 single crystals, ESOMAT 2018, 11th European Symposium on Martensitic Transformations. Metz, France. 27.08. - 31.08.2018

Alfred, I.; Nicolaus, M.; Hermsdorf, J.; Kaierle, S.; Möhwald, K.; Maier, H.-J.; Wesling, V. (2018): Advanced high pressure turbine blade repair technologies, In: 10th CIRP Conference on Photonic Technologies (LANE 2018), Procedia CIRP 74, 2018, S. 214-217
DOI: 10.1016/j.procir.2018.08.097

Krüger, A. K.; Julmi, S.; Klose, C.; Besdo, S.; Maier, H. J.; Wriggers, P. (2018): Simulation of bone ingrowth into bone substitutes on implant level length scale, In: 89th Annual Meeting of the International Association of Applied Mathematics and Mechanics (GAMM). München. 19.3.- 23.3.2018, Proc. Appl. Math. Mech. 18, 2018 (1), e201800297
DOI: 10.1002/pamm.201800297

Klimov, G.; Maier, H-J.; Beniyash, A.; Hassel, T.;  (2018): Fluxless Brazing of aluminum alloys using non vacuum electron beam by 60kV acceleration voltage, Journal of Physics: Conference Series 1109, 2018
DOI: 10.1088/1742-6596/1109/1/011001

Zeitschriften/Aufsätze

Panchenko, E.; Timofeeva, E.; Eftifeeva, A.; Osipovich, K.; Surikov, N.; Chumlyakov, Y.; Gerstein, G.; Maier, H. J. (2018): Giant rubber-like behavior induced by martensite aging in Ni51Fe18Ga27Co4 single crystals, Scripta Materialia 162, 2019, 387-390
DOI: 10.1016/j.scriptamat.2018.12.003

Langen, D.; Maier, H. J.; Hassel, T. (2018): The Effect of SiC Addition on Microstructure and Mechanical Properties of Gas Tungsten Arc-Welded Ti-6Al-4V Alloy, J. of Materi Eng and Perform 27, 2018 (1), 253-260
DOI: 10.1007/s11665-017-3091-y

Spachtholz, J.; Affeldt, E. E.; Maier, H. J.; Hammer, J. (2018): Modelling of the fatigue crack growth of a coated single crystalline nickel-based superalloy under thermal mechanical loading, International Journal of Fatigue 116, 2018, 268-274
DOI: 10.1016/j.ijfatigue.2018.06.015

Angrisani, G. L.; Taptimthong, P.; Thürer, S. E.; Klose, C.; Maier, H. J.; Wurz, M. C.; Möhwald, K. (2018): Magnetic Properties of Thermal Sprayed Tungsten Carbide-Cobalt Coatings, Adv. Eng. Mater. 20, 2018 (9), 1800102
DOI: 10.1002/adem.201800102

Klose, C.; Freytag, P.; Otten, M.; Thürer, S. E.; Maier, H. J. (2018): Thermal Properties of Intermetallic Phases at the Interface of Aluminum-Copper Compound Castings, Adv. Eng. Mater. 20, 2018 (6), 1701027
DOI: 10.1002/adem.201701027

Epishin, A.; Petrushin, N.; Nolze, G.; Gerstein, G.; Maier, H. J. (2018): Investigation of the γ′-Strengthened Quaternary Co-Based Alloys Co-Al-W-Ta, Metall and Mat Trans A 49, 2018 (9), 4042-4057
DOI: 10.1007/s11661-018-4756-3

Żak, A.; Łaszcz, A.; Hasiak, M.; Gerstein, G.; Maier, H. J.; Dudzinski, W. (2018): Ion polishing as a method of imaging the magnetic structures in CoNiGa monocrystal, Results in Physics 10, 2018, 277-280
DOI: 10.1016/j.rinp.2018.06.020

Gerstein, G.; Firstov, G. S.; Kosorukova, T. A.; Koval, Y. N.; Maier, H. J. (2018): Development of B2 Shape Memory Intermetallics Beyond NiAl, CoNiAl and CoNiGa, Shap. Mem. Superelasticity 4, 2018 (3), 360-368
DOI: 10.1007/s40830-018-0180-1

Gerstein, G.; L'vov, V. A.; Żak, A.; Dudziński, W.; Maier, H. J. (2018): Direct Observation of Nano-dimensional Internal Structure of Ferromagnetic Domains in the Ferromagnetic Shape Memory Alloy Co-Ni-Ga, Journal of Magnetism and Magnetic Materials, 2018
DOI: 10.1016/j.jmmm.2018.06.066

Demler, E.; Rodman, D.; Rodman, M.; Gerstein, G.; Grydin, O.; Briukhanov, A. A.; Klose, C.; Nürnberger, F.; Maier, H. J. (2018): The Influence of Alternating Low-Cycle Bending Loads on Sheet Properties Having an Hcp Crystal Lattice, J. of Materi Eng and Perform 27, 2018 (2), 541-549
DOI: 10.1007/s11665-018-3123-2

Bal, B.; Koyama, M.; Canadinc, D.; Gerstein, G.; Maier, H. J.; Tsuzaki, K. (2018): On the Utility of Crystal Plasticity Modeling to Uncover the Individual Roles of Microdeformation Mechanisms on the Work Hardening Response of Fe-23Mn-0.5C TWIP Steel in the Presence of Hydrogen, J. Eng. Mater. Technol 140, 2018 (3), 31002
DOI: 10.1115/1.4038801

Nicolaus, M.; Rottwinkel, B.; Alfred, I.; Möhwald, K.; Nölke, C.; Kaierle, S.; Maier, H. J.; Wesling, V. (2018): Future regeneration processes for high-pressure turbine blades, CEAS Aeronaut J 9, 2018 (1), 85-92
DOI: 10.1007/s13272-017-0277-9

Gerstein, G.; Firstov, G.; Chumlyakov, Y.; Krooß, P.; Niendorf, T.; Dalinger, A.; Maier, H. J. (2018): Magnetic pulse controlled microstructure development in Co 49 Ni 21 Ga 30 single crystals, Materials Science and Technology 34, 2018 (16), 1954-1964
DOI: 10.1080/02670836.2018.1497129

Denkena, B.; Breidenstein, B.; Grove, T.; Prasanthan, V.; Overmeyer, L.; Nothdurft, S.; Kaierle, S.; Wallaschek, J.; Twiefel, J.; Ohrdes, H.; Maier, H. J.; Hassel, T.; Mildebrath, M. (2018): Surface integrity of turned laser-welded hybrid shafts, Prod. Eng. Res. Devel., 2018
DOI: 10.1007/s11740-018-0862-8

Mildebrath, M.; Maier, H. J.; Hassel, T.; Coors, T.; Pape, F.; Poll, G.; Barroi, A.; Lammers, M.; Hermsdorf, J.; Overmayer, L. (2018): Herstellungsprozess und Wälzfestigkeit von hybriden Hochleistungsbauteilen, Konstruktion 70, 2018 (9), 84-89

Nothdurft, S.; Springer, A.; Kaierle, S.; Ohrdes, H.; Twiefel, J.; Wallaschek, J.; Mildebrath, M.; Maier, H. J.; Hassel, T.; Overmeyer, L. (2018): Laser welding of dissimilar low-alloyed steel-steel butt joints and the effects of beam position and ultrasound excitation on the microstructure, Journal of Laser Applications 30, 2018 (3), 32417

Wolf, L. O.; Cordebois, J.-P.; Rodman, D.; Nürnberger, F.; Maier, H. J. (2018): Effect of Different Intercritical Annealing Treatments without and with Overaging on the Mechanical Material Behavior, Steel Research Int. 89, 2018 (10), 1800196
DOI: 10.1002/srin.201800196

Mohammadi, A.; Koyama, M.; Gerstein, G.; Maier, H. J.; Noguchi, H. (2018): Hydrogen-assisted failure in a bimodal twinning-induced plasticity steel: Delamination events and damage evolution, International Journal of Hydrogen Energy 43, 2018 (4), 2492-2502
DOI: 10.1016/j.ijhydene.2017.11.177

Gerstein, G.; L'vov, V. A.; Kosogor, A.; Maier, H. J. (2018): Internal pressure as a key thermodynamic factor to obtain high-temperature superelasticity of shape memory alloys, Materials Letters 210, 2018, 252-254
DOI: 10.1016/j.matlet.2017.09.034

Barton, S.; Reimche, W.; Maier, H.J. (2018): Three-Dimensional Data Storage in the Subsurface Region and Fast Read-Out Technologies for Determining the Mechanical Load History of Components, HTM 73, 2018 (1), 13-26
DOI: 10.3139/105.110343

Demler, E.; Gerstein, G.; Dalinger, A.; Epishin, A.; Heidenblut, T.; Nürnberger, F.; Maier, H. J. (2018): Influence of High Current-Density Impulses on the Stress-Strain Response and Microstructural Evolution of the Single Crystal Superalloy CMSX-4, Materials Research 21, 2018 (6), 1063
DOI: 10.1590/1980-5373-MR-2018-0428

Herbst, S.; Maier, H. J.; Nürnberger, F. (2018): Strategies for the Heat Treatment of Steel-Aluminium Hybrid Components, HTM 73, 2018 (5), 268-282
DOI: 10.3139/105.110368

Toker, S. M.; Gerstein, G.; Maier, H. J.; Canadinc, D. (2018): Effects of microstructural mechanisms on the localized oxidation behavior of NiTi shape memory alloys in simulated body fluid, J Mater Sci 53, 2018 (2), 948-958
DOI: 10.1007/s10853-017-1586-4

Rieck genannt Best, F.; Koch, J.; Lilienkamp, G.; Körkemeyer, F.; Maier, H. J.; Caro, J.; Lange, K. (2018): Spiky Nickel Electrodes for Electrochemical Oxygen Evolution Catalysis by Femtosecond Laser Structuring, International Journal of Electrochemistry, 2018 (12), 1-12
DOI: 10.1155/2018/9875438

Panchenko, E.; Eftifeeva, A.; Chumlyakov, Y.; Gerstein, G.; Maier, H. J. (2018): Two-way shape memory effect and thermal cycling stability in Co 35 Ni 35 Al 30 single crystals by low-temperature martensite ageing, Scripta Materialia 150, 2018, 18-21
DOI: 10.1016/j.scriptamat.2018.02.013

Kadletz, P. M.; Motemani, Y.; Iannotta, J.; Salomon, S.; Khare, C.; Grossmann, L.; Maier, H. J.; Ludwig, A.; Schmahl, W. W. (2018): Crystallographic Structure Analysis of a Ti-Ta Thin Film Materials Library Fabricated by Combinatorial Magnetron Sputtering, ACS combinatorial science 20, 2018 (3), 137-150
DOI: 10.1021/acscombsci.7b00135

Julmi, S.; Krüger, A.-K.; Waselau, A.-C.; Meyer-Lindenberg, A.; Wriggers, P.; Klose, C.; Maier, H. J. (2018): Processing and coating of open-pored absorbable magnesium-based bone implants, Materials Science and Engineering: C 98, 2019, 1073-1086
DOI: 10.1016/j.msec.2018.12.125

Niendorf, T.; Lauhoff, C.; Karsten, E.; Gerstein, G.; Liehr, A.; Krooß, P.; Maier, H. J. (2018): Direct microstructure design by hot extrusion – High-temperature shape memory alloys with bamboo-like microstructure, Scripta Materialia 162, 2019, 127-131
DOI: 10.1016/j.scriptamat.2018.10.051

Patentschriften

Maier, H. J.; Möhwald, K.; Klose, C.; Holländer, U.; Nürnberger, F.; Hassel, T.; Reimche, W.; Rodman, D. (2018): Verfahren zur Herstellung eines Bauteils, Patentschrift: DE 10 2016 121 656 B3, 08.02.2018

Holländer, U.; Wulff, D.; Behrens, B.-A.; Yilkiran, D.; Maier, H.J. (2018): Verfahren zum Oberflächenbeschichten eines Bauteils, Patentschrift: DE 10 2016 114 450 B4, 22.03.2018

2017

Konferenz

Schlobohm, J.; Bruchwald, O.; Frąckowiak, W.; Li, Y.; Kästner, M.; Pösch, A.; Reimche, W.; Maier, H. J.; Reithmeier, E. (2017): Advanced characterization techniques for turbine blade wear and damage, The 5th International Conference on Through-Life Engineering Services. Cranfield, England, 01.11.-02.11.2016, Procedia CIRP 59, 2017, 83-88
DOI: 10.1016/j.procir.2016.09.005

Julmi S., Klose C., Krüger A.-K., Wriggers P., Maier H.J. (2017): Development of Sponge Structure and Casting Conditions for Absorbable Magnesium Bone Implants, In: TMS 2017 146th Annual Meeting & Exhibition Supplemental Proceedings. Springer International Publishing; Springer, Cham, 2017, S. 307-317
DOI: 10.1007/978-3-319-51493-2_29

Jalanesh, M.; Golovko, O.; Gerstein, G.; Hübsch, C.; Hübner, S.; Yarcu, S.; Sezek, O.; Behrens, B.-A.; Rodman, D.; Maier, H. J. (2017): Properties Of Clinched Stainless Steel Sheets As A Result Of Thermal Loading, In: Ya. V. Frolov (Hrsg.): Plastic deformation of metals. Accent PP, Dnipro, 2017, S. 47

Golovko, O.; Puppa, J.; Paschke, H.; Nürnberger, F.; Rodman, D.; Maier, H. J.; Behrens, B.-A. (2017): Properties Of An Intelligent Hot-Working Tool Steel With Alloy Adapted Nitriding Layers, In: Ya. V. Frolov (Hrsg.): Plastic deformation of metals. Accent PP, Dnipro, 2017, S. 49

Nicolaus, M.; Möhwald, K.; Maier, H. J. (2017): Regeneration of High Pressure Turbine Blades. Development of a Hybrid Brazing and Aluminizing Process by means of Thermal Spraying, The 5th International Conference on Through-Life Engineering Services. Cranfield, England, 01.11.-02.11.2016, Procedia CIRP 59, 2017, 72-76
DOI: 10.1016/j.procir.2016.09.041

Nicolaus, M.; Möhwald, K.; Maier, H. J. (2017): Heat treatment of the thermally sprayed coating system NiCrSi/NiCoCrAlY/Al for repair brazing high pressure turbine blades, In: ITSC 2017. DVS-Berichte, Band: 336. DVS Media GmbH, Düsseldorf, 2017, S. 462-466

Bauer, M.; Brand, S.; Schrader, J.; Krettek, C.; Maier, H. J.; Hassel, T. (2017): Local stress investigation of periprosthetic fractures by total hip replacement - a finite element analysis, BMTMedPhys 2017. Poster session 11: Modelling and simulation I. Dresden, 10.09. - 13.09.2017, S. 152
DOI: 10.1515/bmt-2017-5032

Eifler, R.; Schäfke, F.; Maier, H. J.; Klose, C. (2017): Biocompatible Magnesium Alloy ZNdK100 - Adaptation of Extrusion Parameters to Tailor the Mechanical Properties to Different Implant Applications, In: Solanki, K. N. et al. (Hrsg.): Magnesium Technology 2017. Springer International Publishing, 2017, S. 323-327
DOI: 10.1007/978-3-319-52392-7_46

Nothdurft, S.; Springer, A.; Kaierle, S.; Mildebrath, M.; Hassel, T.; Maier, H. J.; Ohrdes, H.; Wallaschek, J.; Overmayer, L. (2017): Fügezonenbeeinflussung beim Laserstrahlschweißen von Stahl-Aluminium- Mischverbindungen zur Verbesserung der Umformeigenschaften, In: Behrens, B.-A. (Hrsg.): Innovationspotenziale in der Umformtechnik. 22. Umformtechnisches Kolloquium Hannover, 15.03.-16.03.2017, Posterbeitrag. TEWISS, Garbsen, 2017, S. 194

Barroi, A.; Mildebrath, M.; Hassel, T.; Hermsdorf, J.; Kaierle, S.; Maier, H. J.; Overmeyer, L. (2017): Erzeugung hybrider Umformhalbzeuge durch Auftragschweißen und Evaluierung der Fügezone vor und nach dem Umformen, In: Behrens, B.-A. (Hrsg.): Innovationspotenziale in der Umformtechnik. 22. Umformtechnisches Kolloquium Hannover, 15.03.-16.03.2017, Posterbeitrag. TEWISS, Garbsen, 2017, S. 195

Thürer, S. E.; Uhe, J.; Golovko, O.; Bonk, C.; Bouguecha, A.; Klose, C.; Behrens, B.-A.; Maier, H. J. (2017): Co-extrusion of semi-finished aluminium-steel compounds, In: Brabazon, D.; Naher, S.; Ahad, I. U. (Hrsg.): Proceedings of the 20th International ESAFORM Conference on Material Forming: ESAFORM 2017. 26-28 April 2017, Dublin, Ireland. AIP Publishing LLC, Melville, New York, 2017, S. 140002
DOI: 10.1063/1.5008158

Bauer, M.; Grünzel, O.; Maier, H. J.; Hassel, T. (2017): Full automatization of waterjet cutting, WJTA-IMCA Conference & Expo 2017. New Orleans. 24.-27.10.2017

Demler, E., Gerstein, G., Dalinger A., Epishin, A., Nürnberger, F., Maier, H. J. (2017): Influence of high-current-density impulses on the plasticity of single crystal nickel-based super alloy CMSX-4, In: Ya. V. Frolov (Hrsg.): Plastic deformation of metals. Accent PP, Dnipro, 2017, S. 47

Wulff, D.; Bornmann, B.; Wagner, R.; Holländer, U.; Lützenkirchen-Hecht, D.; Möhwald, K.; Frahm, R.; Maier, H. J. (2017): In-situ examination of Cr-Ni steel surfaces heat treated under N2 by GIXRD, In: Sternemann, C.; Wagner, R.; Lützenkirchen-Hecht, D. (Hrsg.): 13th DELTA User Meeting & Annual Report 2017. Dortmund. 29.11.2017, S. 27-28

Behrens, B. A.; Maier, H. J.; Hübner, S.; Bonk, C.; Almohallami, A.; Lummer, C.; Schein, P.; Scheland, H.; Micke, M. (2017): Wear Behavior of MoS2 Lubricant Layers During Sheet Metal Forming, In: Proceedings of the 17th International Conference on Sheet Metal SHEMET17, Procedia Engineering 183, 357-362

Wolf, L. O.; Rodman, D.; Nürnberger, F.; Cordebois, J.-P.; Maier, H. J. (2017): Intercritical Annealing – New Heat Treatment Strategies for Tailoring the Stress-Strain Behavior of 22MnB5, In: Oldenburg, M.; Prakash, B.; Steinhoff, K. (Hrsg.): Hot Sheet Metal Forming of High-Performance Steel CHS2. 6th International Conference, 4-7 June 2017, Atlanta, GA., USA. Verlag Wissenschaftliche Scripten, Auerbach, 2017, S. 433-440

Reimche, W.; Bruchwald, O.; Barton, S.; Maier, H. J.; Klümper-Westkamp, H.; Zoch, H.-W. (2017): Inline application of bainite sensor technology for characterizing phase transformation during cooling, Proceedings of: Bainite - from nano to macro. Wiesbaden, 01.06. - 02.06.2017, S. 141-150

Klümper-Westkamp, H.; Vetterlein, J.; Zoch, H.-W.; Reimche, W.; Bruchwald, O.; Maier, H. J. (2017): New bainite sensor technology allows for a detailed view on material transformation, Proceedings of: Bainite - from nano to macro. Wiesbaden, 01.06. - 02.06.2017, S. 133-140

Rodriguez Diaz, M.; Möhwald, K.; Loftfield, N.; Kästner, M.; Reithmeier, E.; Knigge, S.; Glasmacher, B.; Maier, H. J. (2017): Transpiring thermally sprayed alumina layers with integrated fluid flow tubes, In: ITSC 2017. DVS-Berichte, Band: 336. DVS Media GmbH, Düsseldorf, 2017, S. 47-50

Nothdurft, S.; Springer, A.; Kaierle, S.; Mildebrath, M.; Maier, H. J.; Hassel, T.; Ohrdes, H.; Twiefel, J.; Wallaschek, J.; Overmeyer, L. (2017): Influence of beam position and ultrasonic amplitude on the micro-structure of laser welded dissimilar steel-steel joints, In: 36th International Congress on Applications of Lasers & Electro-Optics - ICALEO® 2017. Atlanta, 22.10.-26.10.2017

Beiträge in Büchern

Schilling, T.; Bauer, M.; LaLonde, L.; Maier, H. J.; Haverich, A.; Hassel, T. (2017): Cardiovascular Applications of Magnesium Alloys, In: Aliofkhazraei, M. (Hrsg.): Magnesium Alloys. InTech, Rijeka, Croatia, 2017, S. 191-217
DOI: 10.5772/66182

Barton, S.; Mroz, G.; Reimche, W.; Maier, H. J. (2017): Storing the load history of a component in the subsurface region, In: Denkena, B.; Mörke, T. (Hrsg.): Cyber-physical and gentelligent systems in manufacturing and life cycle. Elsevier, London, 2017, S. 67-84

Barton, S.; Mroz, G.; Reimche, W.; Maier, H. J. (2017): Data storage within the subsurface of a component by local heat treatment, In: Denkena, B.; Mörke, T. (Hrsg.): Cyber-physical and gentelligent systems in manufacturing and life cycle. Elsevier, London, 2017, S. 85-99

Zeitschriften/Aufsätze

Kokorin, V. V.; Konoplyuk, S. M.; Dalinger, A.; Maier, H. J. (2017): Influence of martensitic transformation on the magnetic transition in Ni-Mn-Ga, Journal of Magnetism and Magnetic Materials 432, 2017, 266-270
DOI: 10.1016/j.jmmm.2017.02.008

Gerstein, G.; Clausmeyer, T.; Isik, K.; Nürnberger, F.; Tekkaya, A. E.; Bruchanov, A. A.; Maier, H.J. (2017): Experimental analysis of anisotropic damage in dual-phase steel by resonance measurement, International Journal of Damage Mechanics 26, 2016 (8), 1147-1169
DOI: 10.1177/1056789516650245

Otten, M.; Klose, C.; Möhwald, K.; Knödler, P.; Maier, H. J. (2017): Untersuchung der Serientauglichkeit des Schichttransplantationsprozesses zur Herstellung von beschichteten Druckgussbauteilen, Giesserei Special, 2017 (1), 74-89

Maier, H. J.; Karsten, E.; Paulsen, A.; Langenkämper, D.; Decker, P.; Frenzel, J.; Somsen, C.; Ludwig, A.; Eggeler, G.; Niendorf, T. (2017): Microstructural evolution and functional fatigue of a Ti–25Ta high-temperature shape memory alloy, J. Mater. Res. 32, 2017 (23), 4287-4295
DOI: 10.1557/jmr.2017.319

Nicolaus, M.; Möhwald, K.; Maier, H. J. (2017): A Combined Brazing and Aluminizing Process for Repairing Turbine Blades by Thermal Spraying Using the Coating System NiCrSi/NiCoCrAlY/Al, J Therm Spray Tech 26, 2017 (7), 1659-1668
DOI: 10.1007/s11666-017-0612-z

Zhao, S.; Seitz, J.-M.; Eifler, R.; Maier, H. J.; Guillory, R. J.; Earley, E. J.; Drelich, A.; Goldman, J.; Drelich, J. W. (2017): Zn-Li alloy after extrusion and drawing: Structural, mechanical characterization, and biodegradation in abdominal aorta of rat, Materials Science and Engineering: C 76, 2017, 301-312
DOI: 10.1016/j.msec.2017.02.167

Gerstein, G.; Besserer, H.-B.; Nürnberger, F.; Barrales-Mora, L. A.; Shvindlerman, L. S.; Estrin, Y.; Maier, H. J. (2017): Formation and growth of voids in dual-phase steel at microscale and nanoscale levels, Journal of Materials Science 52, 2017 (8), 4234-4243
DOI: 10.1007/s10853-016-0678-x

Nürnberger, F.; Gerstein, G.; Dalinger, A.; Thürer, S. E.; Vinogradov, A.; Feldhoff, A.; Maier, H. J. (2017): Surface modification of an austenitic stainless steel wire by a multi-pulse treatment with a high-power electric current, Journal of Materials Science 52, 2017 (13), 8007-8015
DOI: 10.1007/s10853-017-1003-z

Gerstein, G.; L’vov, V.; Chumlyakov, Y.; Niendorf, T.; Krooß, P.; Dalinger, A.; Heidenblut, T.; Maier, H. J. (2017): Pulsed magnetic field-induced changes in the meso- and nanostructure of Co49Ni21Ga30 martensite, Funct. Mater. Lett. 10, 2017 (04), 1750044
DOI: 10.1142/S1793604717500448

Panchenko, E.; Timofeeva, E. E.; Larchenkova, N. G.; Chumlyakov, Y.; Tagiltsev, A. I.; Maier, H. J.; Gerstein, G. (2017): Two-way shape memory effect under multi-cycles in [001]-oriented Ni 49 Fe 18 Ga 27 Co 6 single crystal, Materials Science and Engineering: A 706, 2017, 95-103
DOI: 10.1016/j.msea.2017.08.108

Yilkiran, D.; Wulff, D.; Özkaya, F.; Hübner, S.; Holländer, U.; Maier, H. J.; Behrens, B.-A. (2017): Wear Testing of Thermally Oxidised Tool Steel Specimens with α-Fe2O3 Layers, Dry Met. Forming OAJ FMT 3, 2017, 45-49

Herbst, S.; Aengeneyndt, H.; Maier, H. J.; Nürnberger, F. (2017): Microstructure and Mechanical Properties of Friction Welded Steel-Aluminum Hybrid Components after T6 Heat Treatment, Materials Science and Engineering: A 696, 2017, 33-41
DOI: 10.1016/j.msea.2017.04.052

Timofeeva, E. E.; Panchenko, E. Y.; Chumlyakov, Y. I.; Maier, H. J.; Gerstein, G. (2017): Peculiarities of high-temperature superelasticity in Ni–Fe–Ga single crystals in compression, Tech. Phys. Lett. 43, 2017 (3), 320-323
DOI: 10.1134/S1063785017030245

Astafurova, E. G.; Moskvina, V. A.; Maier, G. G.; Melnikov, E. V.; Zakharov, G. N.; Astafurov, S. V.; Maier, H. J. (2017): Hydrogen-enhanced Orientation Dependence of Stress Relaxation and Strain-aging in Hadfield Steel Single Crystals, Scripta Materialia 136, 2017, 101-105
DOI: 10.1016/j.scriptamat.2017.04.028

Bagehorn, S.; Wehr, J.; Maier, H. J. (2017): Application of mechanical surface finishing processes for roughness reduction and fatigue improvement of additively manufactured Ti-6Al-4V parts, International Journal of Fatigue 102, 2017, 135-142
DOI: 10.1016/j.ijfatigue.2017.05.008

Astafurova, E.; Maier, G.; Melnikov, E.; Naydenkin, E.; Smirnov, A.; Bataev, V.; Odessky, P.; Dobatkin, S.; Maier, H. J. (2017): The Influence of the Thermomechanical Processing Regime on the Structural Evolution of Mo-Nb-Ti-V Microalloyed Steel Subjected to High-Pressure Torsion, Metall and Mat Trans A 48, 2017 (7), 3400-3409
DOI: 10.1007/s11661-017-4085-y

Wolf, L. O.; Nürnberger, F.; Rodman, D.; Maier, H. J. (2017): The Effect of Intercritical Annealing on the Microstructure and Mechanical Properties of Ferritic-Martensitic Two-Phase Steels, Steel Research Int. 88, 2017 (2), 271-280
DOI: 10.1002/srin.201600107

Wolf, L. O.; Nürnberger, F.; Rodman, D.; Maier, H. J. (2017): 1-Step “Quenching and Partitioning” of the Press-Hardening Steel 22MnB5, Steel Research Int. 88, 2017 (6), 1600307
DOI: 10.1002/srin.201600307

Leschke, J.; Hecht-Linowitzki, V.; Hassel, T.; Hermsdorf, J.; Kaierle, S.; Overmayer, L.; Maier, H. J. (2017): Laserstrahlschneiden unter Wasser für höhere Produktivität, Schweißen und Schneiden 69, 2017 (11), 774-780

Almohallami, A.; Arghavani, M.; Böhmermann, F.; Freiße, H.; Herrmann, M.; Mousavi, S. A.; Schöler, S.; Scholz, P.; Tenner, J.; Teller, M.; Umlauf, G.; Wulff, D.; Yilkiran, D.; Maier, H. J. (2017): How dry is dry? - A critical analysis of surface conditions used in dry metal forming, Dry Met. Forming OAJ FMT 3, 2017, 90-94

Yilkiran, D.; Wulff, D.; Almohallami, A.; Özkaya, F.; Bouguecha, A.; Hübner, S.; Möhwald, K.; Maier, H. J.; Behrens, B.-A. (2017): Wear behaviour of thermally oxidised tool surfaces as low-friction separation layers for dry sheet metal forming, Wear 376-377, 2017, 1789-1803
DOI: 10.1016/j.wear.2017.01.084

Reschka, S.; Munk, L.; Wriggers, P.; Maier, H. J. (2017): An EBSD Evaluation of the Microstructure of Crept Nimonic 101 for the Validation of a Polycrystal–Plasticity Model, J. of Materi Eng and Perform 26, 2017 (12), 6087-6098
DOI: 10.1007/s11665-017-3046-3

Mildebrath, M.; Somonov, V.; Nothdurft, S.; Ohrdes, H.; Springer, A.; Kaierle, S.; Hassel, T.:, Maier, H.-J.; Wallascheck, J. (2017): Influence of silicon on the structure and weldability of steel-aluminium joints processed by non-vacuum electron beam welding, International Journal of Emerging Technology and Advanced Engineering 7, 2017 (9), 348-356

Mildebrath, M.; Blohm, T.; Hassel, T.; Stonis, M.; Langner, J.; Maier, H. J.; Behrens, B.-A. (2017): Influence of Cross Wedge Rolling on the Coating Quality of Plasma-Transferred Arc Deposition Welded Hybrid Steel Parts, International Journal of Emerging Technology and Advanced Engineering 7, 2017 (7), 1-7

Patentschriften

Klose, C; Maier H.J.; Grittner, N.; Engelhardt, M. (2017): Verfahren zur Herstellung eines metallischen Bauteils, metallisches Bauteil und Vorrichtung zur Herstellung eines metallischen Bauteils, Patentschrift: DE 10 2014 109 764 B4, 20.07.2017

Engelhardt, M.; Grittner, N.; Klose, C.; Maier H.J. (2017): Verfahren zum Strangpressen, Strangpressvorrichtung sowie Strangpresswerkzeug, Patentschrift: DE102015107308, 19.10.2017

Klose, C.; Hassel, T.; Nürnberger, F.; Maier, H.J.;  (2017): Verfahren zur Herstellung eines Hybridzahnrads sowie Hybridzahnrad, Patentschrift: DE102015102297, 31.08.2017

2016

Konferenz

Bruchwald, O.; Frackowiak, W.; Zwoch, S.; Reimche, W.; Maier, H. J. (2016): In-Situ Monitoring of the Microstructure Evolution Using Eddy Current Technology, Proceedings of the 19th World Conference on Non-Destructive Testing WCNDT, München, 2016

Bruchwald, O.; Nicolaus, M.; Frackowiak, W.; Möhwald, K.; Reimche, W.; Maier, H. J. (2016): Material Characterization of Thin Coatings Using High Frequency Eddy Current Technology, Proceedings of the 19th World Conference on Non-Destructive Testing WCNDT, München, 2016

Frackowiak, W.; Bruchwald, O.; Zwoch, S.; Reimche, W.; Maier, H. J. (2016): Non-Destructive Damage Detection and Material Characterization of Turbine Components Using Megahertz Range Induction Thermography in Pulsed Mode, Proceedings of the 19th World Conference on Non-Destructive Testing WCNDT, München, 2016

Aldag, D.; Varahram, A.; Lehr, J.; Maier, H.; Hassel, T. (2016): Fügen von Casingsegmenten mit dem MIAB-Schweißverfahren für die Anwendung am Bohrturm, In: DGMK/ÖGEW-Frühjahrstagung des Fachbereiches Aufsuchung und Gewinnung am 21. und 22. April 2016 in Celle. Deutsche Wissenschaftliche Gesellschaft für Erdöl, Erdgas und Kohle e.V, Hamburg, 2016, S. 139-148

Gerstein, G.; Nürnberger, F.; Maier, H. J. (2016): Evolution of void shape anisotropy in deformed bcc steels, In: 145. TMS Annual Meeting & Exhebition, Proceedings of the Epd Congress 2016. John Wiley & Sons, Inc., Hoboken, New Jersey, 2016, S. 173-179

Eifler, R.; Durisin, M.; Klose, C.; Lenarz, T.; Maier, H. J. (2016): Degradation of MgF2-Coated and Uncoated MgNd2 Specimens in Contact with Nasal Mucosa, In: 145. TMS Annual Meeting & Exhebition, Magnesium technology 2016. John Wiley & Sons, Inc., Hoboken, New Jersey, 2016, S. 331-335

Wolf, L.; Rodman, D.; Maier, H. J.; Nürnberger, F. (2016): Adapted multi-phase microstructures by intercritical annealing and press hardening, In: Furuhara, T.; Nishida, M.; Miura S. (Hrsg.): The Ninth Pacific Rim International Conference on Advanced Materials and Processing (PRICM9). Kyoto, Japan. 01.-05. Aug. 2016. Wiley-VCH, 2016, S. 295-298

Knödler, P.; Otten, M.; Freiburg, D.; Möhwald, K.; Maier, H. J.; Biermann, D. (2016): Transplantation of Micro- and Nanostructured Coatings by Means of Thermal Spraying and PVD, In: K. Bobzin, K.-D. Bouzakis, B. Denkena, H. J. Maier, M. Merklein (Hrsg.): The „A“ Coatings 2016. Conference Proceedings. PZH-Verlag, Garbsen, 2016, S. 3-11

Hassel, T.; Langen, D.; Maier, H. J. (2016): Gefüge und mechanische Eigenschaften impfbehandelter Schweißnähte an Titan, In: DVS Congress 2016. Große Schweißtechnische Tagung, Leipzig, 19. und 20. September 2016, S. 49-53

Frackowiak, W.; Bruchwald, O.; Reimche, W.; Maier, H. J. (2016): Applications of high frequency induction thermography in themegahertz range for material characterization of turbine components, In: K. Bobzin, K.-D. Bouzakis, B. Denkena, H. J. Maier, M. Merklein (Hrsg.): The „A“ Coatings 2016. Conference Proceedings. PZH-Verlag, Garbsen, 2016, S. 31-36

Bruchwald, O.; Frackowiak, W.; Reimche, W.; Maier, H. J. (2016): Applications of high frequency eddy current technology for material characterization of thin coatings, In: K. Bobzin, K.-D. Bouzakis, B. Denkena, H. J. Maier, M. Merklein (Hrsg.): The „A“ Coatings 2016. Conference Proceedings. PZH-Verlag, Garbsen, 2016, S. 37-43

Barton, S.; Mroz, G.; Reimche, W.; Maier, H. J. (2016): Inherent Load Measurement and Component Identification by multi-dimensional Coded Data in the Component's Subsurface Region, In: Procedia Technology. 3rd International Conference on System-Integrated Intelligence. Paderborn. 13.06. - 15.06.2016. Elsevier, Amsterdam, 2016, S. 537-543
DOI: 10.1016/j.protcy.2016.08.067

Schmidt, H. C.; Homberg, W.; Hoppe, C.; Grundmeier, G.; Hordych, I.; Maier, H. J. (2016): Cold pressure welding by incremental rolling: Deformation zone analysis, In: Chinesta, F.; Cueto, E.; Abisset-Chavanne, E. (Hrsg.): Proceedings of the 19th International ESAFORM Conference on Material Forming: ESAFORM 2016. Nantes, France. 27-29 April 2016. AIP Publishing LLC, Melville, New York, S. 100013

Wolf, L.; Nürnberger, F.; Rodman, D.; Boiarkin, V.; Maier, H. J. (2016): Manufacturing of multiphase steel with adapted material properties, In: Special Workshop Multiscale Modeling of Heterogeneous Structures. 21.-23. Sept. 2016, Dubrovnik, Kroatien

Demminger, C.; Klose, C.; Maier, H. J. (2016): Microstructure and Magnetic Properties of Cobalt and Zinc Containing Magnesium Alloys, In: Procedia Technology. 3rd International Conference on System-Integrated Intelligence. Paderborn. 13.06. - 15.06.2016. Elsevier, Amsterdam, 2016, S. 35-42
DOI: 10.1016/j.protcy.2016.08.006

Golovko, O.; Puppa, J.; Nürnberger, F.; Rodman, D.; Maier, H. J.; Behrens, B.-A. (2016): Development of intelligent hot forging tools with increased wear resistance by cyclic edge-zone hardening, In: Proceedings of the 10th TOOL Conference 2016. Bratislava, Slowakei. 04.10. - 07.10.2016, S. 316-325

Bruchwald, O.; Frackowiak, W.; Reimche, W.; Maier, H. J. (2016): In-Situ Monitoring of the Microstructure Evolution, In: ATZK - Association for the Heat Treatment of Metals (Hrsg.): Proceedings of the European Conference on Heat Treatment 2016 and 3rd International Conference on Heat Treatment and Surface Engineering in Automotive Applications. 10.05. - 13.05.2016, Prague, Czech Republic

Yilkiran, D.; Wulff, D.; Almohallami, A.; Holländer, U.; Hübner, S.; Möhwald, K.; Behrens, B.-A., Maier, H. J. (2016): Selectively Oxidised Tool Steel Surfaces for Sheet Metal Forming, In: K. Bobzin, K.-D. Bouzakis, B. Denkena, H. J. Maier, M. Merklein (Hrsg.): The „A“ Coatings 2016. Conference Proceedings. PZH-Verlag, Garbsen, 2016, S. 179-185

U. Holländer, F. Weber, D. Wulff, K. Möhwald, H.J. Maier, M. Müller, I. Scharf, T. Lampke (2016): Development of a combined brazing-nitriding process for the production of bipolar plates made of chromium coated metal sheets, In: DVS (Hrsg.): Brazing, high temperature brazing and diffusion bonding - LÖT 2016. Aachen, 07.06. - 09.06.2016. DVS Media, 2016, S. 174-180

Wulff, D.; Holländer, U.; Lützenkirchen-Hecht, D.; Langohr, A.; Möhwald, K.; Maier, H. J. (2016): Short-time nitridation of electroplated chromium coatings in SiH4-doped N2- atmosphere analysed by GIXRD, In: Sternemann, C.; Wagner, R.; Lützenkirchen-Hecht, D. (Hrsg.): 12th DELTA User Meeting & Annual Report 2016. Dortmund, 30.11.2016, S. 53-54

F. Weber, U. Holländer, J. Schaup, K. Möhwald, H. J. Maier (2016): Fluxfree brazing of copper based alloys and steels at temperatures between 650 °C and 850 °C in monosilane-doped nitrogen, In: DVS (Hrsg.): Brazing, high temperature brazing and diffusion bonding - LÖT 2016. Aachen, 07.06. - 09.06.2016. DVS Media, 2016, S. 186-191

M. Schmieding, U. Holländer, K. Möhwald, H. J. Maier (2016): Development of copper and nickel based brazing solders with a low brazing and a high remelting temperature, In: DVS (Hrsg.): Brazing, high temperature brazing and diffusion bonding - LÖT 2016. Aachen, 07.06. - 09.06.2016. DVS Media, 2016, S. 272-277

Beiträge in Büchern

Knödler, P.; Bathe, T.; Möhwald, K.; Maier, H. J.; Biermann, D. (2016): Verfahren und Methoden zur Transplantation thermisch gespritzter Schichten für Druckgussteile, In: Biermann, D. (Hrsg.): Spanende Fertigung. Prozesse, Innovationen, Werkstoffe. Vulkan, Essen, 2016, S. 88-93

Zeitschriften/Aufsätze

Besserer, H.-B.; Dalinger, A.; Rodman, D.; Nürnberger, F.; Hildenbrand, P.; Merklein, M.; Maier, H. J. (2016): Induction heat treatment of sheet-bulk metal-formed parts assisted by water-air spray cooling, Steel Research Int. 87, 2016 (9), 1220-1227
DOI: 10.1002/srin.201500404

Herbst, S.; Besserer, H.-B.; Grydin, O.; Milenin, A.; Maier, H. J.; Nürnberger, F. (2016): Holistic consideration of grain growth behavior of tempering steel 34CrNiMo6 during heating processes, Journal of Materials Processing Technology 229, 2016, 61-71
DOI: 10.1016/j.jmatprotec.2015.09.015

Isik, K.; Gerstein, G.; Schneider, T.; Schulte, R.; Rosenbusch, D.; Clausmeyer, T.; Nürnberger, F.; Vucetic, M.; Koch, S.; Hübner, S.; Behrens, B.-A.; Tekkaya, A. E.; Merklein, M. (2016): Investigations of ductile damage during the process chains of toothed functional components manufactured by sheet-bulk metal forming, Production Engineering 10, 2016 (1), 5-15
DOI: 10.1007/s11740-016-0656-9

Uzer, B.; Toker, S. M.; Cingoz, A.; Bagci-Onder, T.; Gerstein, G.; Maier, H. J.; Canadinc, D. (2016): An exploration of plastic deformation dependence of cell viability and adhesion in metallic implant materials, Journal of the Mechanical Behavior of Biomedical Materials 60, 2016, 177-186
DOI: 10.1016/j.jmbbm.2016.01.001

Isik, K.; Gerstein, G.; Gutknecht, F.; Clausmeyer, T.; Nürnberger, F.; Maier, H. J.; Tekkaya, A. E. (2016): Investigations of ductile damage in DP600 and DC04 deep drawing steel sheets during punching, Procedia Structural Integrity 2, 2016, 673-680
DOI: 10.1016/j.prostr.2016.06.087

Besserer, H.-B.; Hildenbrand, P.; Gerstein, G.; Rodman, D.; Nürnberger, F.; Merklein, M.; Maier, H. J. (2016): Ductile Damage and Fatigue Behavior of Semi-Finished Tailored Blanks for Sheet-Bulk Metal Forming Processes, Journal of Materials Engineering and Performance 25, 2016 (3), 1136-1142
DOI: 10.1007/s11665-016-1908-8

Besserer, H.-B.; Gerstein, G.; Maier, H. J.; Nürnberger, F. (2016): Specimen Preparation by Ion Beam Slope Cutting for Characterization of Ductile Damage by Scanning Electron Microscopy, Microsc. Res. Tech. 79, 2016 (4), 321-327
DOI: 10.1002/jemt.22633

Bruchwald, O.; Frąckowiak, W.; Reimche, W.; Maier, H. J. (2016): Sensor-controlled bainitic transformation and microstructure formation of forgings during the cooling process, Mat.-wiss. u. Werkstofftech 47, 2016 (8), 780-788
DOI: 10.1002/mawe.201600612

Onal, O.; Gumus, B.; Aksoy, B.; Gerstein, G.; Alaca, B. E.; Maier, H. J.; Canadinc, D. (2016): Micro-Scale Cyclic Bending Response of NiTi Shape Memory Alloy, Materials Transactions 57, 2016 (3), 472-475
DOI: 10.2320/matertrans.M2015423

Hoppe, C.; Ebbert, C.; Voigt, M.; Schmidt, H. C.; Rodman, D.; Homberg, W.; Maier, H. J.; Grundmeier, G. (2016): Molecular Engineering of Aluminum-Copper Interfaces for Joining by Plastic Deformation, Adv. Eng. Mater. 18, 2016 (6), 1066-1074
DOI: 10.1002/adem.201500501

Eifler, R.; Seitz, J. M.; Weber, C. M.; Grundke, S.; Reifenrath, J.; Kietzmann, M.; Lenarz, T. H.; Maier, H. J.; Klose, C.; Durisin, M. (2016): MgNd2 alloy in contact with nasal mucosa: an in vivo and in vitro approach, J Mater Sci: Mater Med 27, 2016 (2), 25
DOI: 10.1007/s10856-015-5636-7

Krooß, P.; Kadletz, P. M.; Somsen, C.; Gutmann, M. J.; Chumlyakov, Y. I.; Schmahl, W. W.; Maier, H. J.; Niendorf, T. (2016): Cyclic Degradation of Co49Ni21Ga30 High-Temperature Shape Memory Alloy: On the Roles of Dislocation Activity and Chemical Order, Shap. Mem. Superelasticity 2, 2016 (1), 37-49
DOI: 10.1007/s40830-015-0049-5

Herbst, S.; Steinke, K. F.; Maier, H. J.; Milenin, A.; Nürnberger, F. (2016): Determination of heat transfer coefficients for complex spray cooling arrangements, International Journal of Microstructure and Materials Properties 11, 2016 3/4, 229-246
DOI: 10.1504/IJMMP.2016.079149

Isik, K.; Gerstein, G.; Clausmeyer, T.; Nürnberger, F.; Tekkaya, A. E.; Maier, H. J. (2016): Evaluation of Void Nucleation and Development during Plastic Deformation of Dual-Phase Steel DP600, Steel Research Int. 87, 2016 (12), 1583-1591
DOI: 10.1002/srin.201500483

Herbst, S.; Schledorn, M.; Maier, H. J.; Milenin, A.; Nürnberger, F. (2016): Process Integrated Heat Treatment of a Microalloyed Medium Carbon Steel: Microstructure and Mechanical Properties, J. of Materi Eng and Perform 25, 2016 (4), 1453-1462
DOI: 10.1007/s11665-016-2004-9

Hordych, I.; Rodman, D.; Nürnberger, F.; Hoppe, C.; Schmidt, H. C.; Grundmeier, G.; Homberg, W.; Maier, H. J. (2016): Effect of Pre-Rolling Heat Treatments on the Bond Strength of Cladded Galvanized Steels in a Cold Roll Bonding Process, Steel Research Int. 87, 2016 (12), 1619-1626
DOI: 10.1002/srin.201600021

Puppa, J.; Dinkel, S.; Behrens, B.-A.; Maier, H. J. (2016): Intelligente Schmiedewerkzeuge – Effizienter Verschleißschutz durch zyklische Randschichthärtung?, massivUMFORMUNG, 2016 (3), 44-48

Bal, B.; Koyama, M.; Gerstein, G.; Maier, H. J.; Tsuzaki, K. (2016): Effect of strain rate on hydrogen embrittlement susceptibility of twinning-induced plasticity steel pre-charged with high-pressure hydrogen gas, International Journal of Hydrogen Energy 41, 2016 (34), 15362-15372
DOI: 10.1016/j.ijhydene.2016.06.259

Lehmann, R.; Schmidt, H. J.; Costa, B. F. O.; Blumers, M.; Sansano, A.; Rull, F.; Wengerowsky, D.; Nürnberger, F.; Maier, H. J.; Klingelhöfer, G.; Renz, F. (2016): 57Fe Mössbauer, SEM/EDX, p-XRF and μ-XRF studies on a Dutch painting, Hyperfine Interact 237, 2016 (1)
DOI: 10.1007/s10751-016-1296-3

Hoppe, C.; Ebbert, C.; Grothe, R.; Schmidt, H. C.; Hordych, I.; Homberg, W.; Maier, H. J.; Grundmeier, G. (2016): Influence of the Surface and Heat Treatment on the Bond Strength of Galvanized Steel/Aluminum Composites Joined by Plastic Deformation, Adv. Eng. Mater. 18, 2016 (8), 1371-1380
DOI: 10.1002/adem.201600085

Schlobohm, J.; Bruchwald, O.; Frackowiak, W.; Li, Y.; Kästner, M.; Pösch, A.; Reimche, W.; Reithmeier, E.; Maier, H. J. (2016): Turbine blade wear and damage – An overview of advanced characterization techniques, Materials Testing 58, 2016 (5), 389-394
DOI: 10.3139/120.110872

Brand, S.; Bauer, M.; Petri, M.; Schrader, J.; Maier, H. J.; Krettek, C.; Hassel, T. (2016): Impact of intraprosthetic drilling on the strength of the femoral stem in periprosthetic fractures: A finite element investigation, In: Proceedings of the Institution of Mechanical Engineers, Part H: Journal of Engineering in Medicine 230, 2016 (7), 675-681
DOI: 10.1177/0954411916647078

Gerstein, G.; Clausmeyer, T.; Isik, K.; Nürnberger, F.; Tekkaya, A. E.; Bruchanov, A. A.; Maier, H. J. (2016): Experimental analysis of anisotropic damage in dual-phase steel by resonance measurement, International Journal of Damage Mechanics, 2016
DOI: 10.1177/1056789516650245

Lützenkirchen-Hecht, D.; Wulff, D.; Wagner, R.; Holländer, U.; Maier, H. J.; Frahm, R. (2016): Ex-situ and in-situ investigations of thermal anti-oxidation treatments of stainless steels by reflection mode EXAFS, J. Phys.: Conf. Ser. 712, 2016, 12047
DOI: 10.1088/1742-6596/712/1/012047

Yilkiran, D.; Almohallami, A.; Wulff, D.; Hübner, S.; Vucetic, M.; Maier, H.; Behrens, B.-A. (2016): New Specimen Design for Wear Investigations in Dry Sheet Metal Forming, Dry Met. Forming OAJ FMT 2, 2016, 62-66

Rahim, M. I.; Tavares, A.; Evertz, F.; Kieke, M.; Seitz, J.-M.; Eifler, R.; Weizbauer, A.; Willbold, E.; Maier, H. (2016): Phosphate conversion coating reduces the degradation rate and suppresses side effects of metallic magnesium implants in an animal model, J. Biomed. Mater. Res., 2016
DOI: 10.1002/jbm.b.33704

Vogel, F.; Abrahams, H.; Biermann, D.; Nicolaus, M.; Rodriguez Diaz, M.; Möhwald, K.; Maier, H. J. (2016): Formschlüssige Substratanbindung thermisch gespritzter Schichten durch die Verfahrenskombination Rändelfräsen und Festwalzen, Werkstoffe in der Fertigung, 2016 (4), 27-28

Nicolaus, M.; Möhwald, K.; Maier, H. J.; Abrahams, H.; Vogel, F.; Biermann, D. (2016): Geometrisch bestimmte Oberflächenstrukturen zur formschlüssigen Substratanbindung thermisch gespritzter Schichten, Thermal Spray Bulletin 68, 2016 (1), 54-59

Taube, A.; Kurtovic, A.; Niendorf, T.; Mertens, T.; Zinn, C.; Schaper, M.; Maier, H. J. (2016): Influence of surface pre-treatments on the high-cycle fatigue behavior of Ti–6Al–4V – From anodizing to laser-assisted techniques, International Journal of Fatigue 91, 2016, 195-203
DOI: 10.1016/j.ijfatigue.2016.06.010

Holländer, U.; Weber, F.; Möhwald, K.; Maier, H. J. (2016): Entwicklung von Prozessen zum flussmittelfreien Schutzgas-Hartlöten zwischen 650 und 850 °C durch Einsatz silandotierter Prozessgase, Schweißen und Schneiden 68, 2016 (5)

Alkan, S.; Chowdhury, P.; Sehitoglu, H.; Rateick, R. G.; Maier, H. J. (2016): Role of nanotwins on fatigue crack growth resistance – Experiments and theory, International Journal of Fatigue 84, 2016, 28-39
DOI: 10.1016/j.ijfatigue.2015.11.012

Kiliclar, Y.; Demir, O. K.; Engelhardt, M.; Rozgić, M.; Vladimirov, I. N.; Wulfinghoff, S.; Weddeling, C.; Gies, S.; Klose, C.; Reese, S.; Tekkaya, A. E.; Maier, H. J.; Stiemer, M. (2016): Experimental and numerical investigation of increased formability in combined quasi-static and high-speed forming processes, Journal of Materials Processing Technology 237, 2016, 254-269
DOI: 10.1016/j.jmatprotec.2016.06.007

2015

Konferenz

Gerstein, G.; Besserer, H.-B.; Nürnberger, F.; Maier, H. J. (2015): Comparsion of the mechanisms of void formation by plastic deformation in single- and dual-phase bcc-steels, Proceedings of the TMS 2015 Annual Meeting 2015, Characterization of minerals, metals, and materials, Orlando, Florida, 15.-19.03.2015. Hoboken, New Jersey: John Wiley & Sons, Inc, S. 75–81
DOI: 10.1002/9781119093404.ch9

Bauer, M.; Müller-Deile, H.; Schilling, T.; Kaufeld, K. T.; Weidling, M.; Wriggers, P.; Haverich, A.; Maier, H. J.; Hassel, T. (2015): Characterisation of native stomach tissue of swine by uniaxial tensile testing, Biomed Tech 2015, DGBMT, 60 (s1), 108-109
DOI: 10.1515/bmt-2015-5004

Bruchwald, O.; Frackowiak, W.; Reimche, W.; Maier, H. J. (2015): Sensor-controlled bainitic transformation and microstructure formation of forgings during the cooling process, In: Zoch, H.-W.; Lübben, T. (Hg.): Proceedings of the 5th International Conference on Distortion Engineering, 2015; S. 319–328.

Herbst, S.; Steinke, K. -F; Maier, H. J.; Milenin, A.; Nürnberger, F. (2015): Determination of heat transfer coefficients for complex spray cooling arrangements, In: Zoch, H.-W.; Lübben, T. (Hg.): Proceedings of the 5th International Conference on Distortion Engineering, 2015; S. 247–256

Klose, C.; Demminger, C.; Maier, H. J. (2015): Microstructure and Properties of Cobalt- and Zinc-Containing Magnetic Magnesium Alloys Processed by High-Pressure Die Casting, In: Manuel, M. V. et al. (Hg.): Magnesium Technology 2015. Proceedings of a symposium sponsored by Magnesium Committee of the Light Metals Division of The Minerals, Metals & Materials Society (TMS), 144th Annual Meeting & Exhibition, 15.-19.03.2015, Orlando, Florida. John Wiley & Sons, Inc., Hoboken, New Jersey, 2015; S. 451-454

Reimche, W.; Bruchwald, O.; Frackowiak, W.; Maier, H. J. (2015): Sensorkontrollierte Bainitumwandlung aus der Schmiedewärme bei modernen Hochleistungsbauteilen im Leichtbau, Werkstoffwoche 2015, Dresden, 14. - 17.09.2015

Kokorin, V.V., Konoplyuk, S.M., Dalinger, A., Thürer, S., Gerstein, G., Mashirov, A., Stetskiv, Y.P., Maier, H.J. (2015): Stress-induced transformation on Ni-Mn-In alloy and the concomitant change of resistivity, 10th European Symposium on Martensitic Transformations (ESOMAT 2015), Poster presentation, 14. - 17. September 2015, Antwerpen.

Knödler, P.; Otten, M.; Möhwald, K.; Maier, H. J.; Freiburg, D.; Peuker, A.; Biermann, D. (2015): Transplantation of Thermal Sprayed Coatings, ASM International (Hrsg.): Thermal Spray 2015. Proceedings from the International Thermal Spray Conference and Exposition. ASM International, Materials Park, Ohio, 2015; S. 753-755

Behrens, B.-A.; Maier, H. J.; Nürnberger, F.; Schrödter, J.; Moritz, J.; Wolf, L.; Gaebel C. M. (2015): Hot forming and subsequent cooling outside the press for adjusted tailored properties of 22MnB5 steel sheets, In: Steinhoff, K.; Oldenburg, M.; Prakash, B. (Hg.): Hot Sheet Metal Forming of High Performance Steel. 5th International Conference Proceedings CHS2. Verl. Wiss. Scripten, Auerbach; S. 35-44.

Zimmermann, S.; Schmettlach, S.; Weber, S.; Marques, J.; Forster, G.; Landes, K.; Schein, J.; Lummer, C.; Knödler, P.; Kresnik, S.; Prehm, J.; Möhwald, K.; Maier, H. J. (2015): Homogenization of Coating Properties in Three-Cathode Atmospheric Plasma Spraying by Use of Advanced Diagnostics and Numerical Simulation - Investigations of Suspension Plasma Spraying (SPS), In: ASM International (Hrsg.): Proceedings from the International Thermal Spray Conference 2015; S. 452-459

Zaremba, D.; Heese, P.; Bauer, M.; Maier, H. J.; Hassel, T. (2015): Particle Disintegration in the Abrasive Water Injection Jet, WJTA-IMCA Conference and Expo, 2.-4. November 2015, New Orleans, Louisiana

Bauer, M.; Grünzel, O.; Zaremba, D.; Maier, H. J.; Hassel, T.; (2015): Spectral measurement of element solubility in water up to 300 MPa, WJTA-IMCA Conference and Expo, 2.-4. November 2015, New Orleans, Louisiana

Bruchwald, O.; Frackowiak, W.; Reimche, W.; Maier, H. J. (2015): Non-destructive in situ monitoring of the microstructural development in high performance steel components during heat treatment, In: Associazone Italiana di Metallurgia (AIM) (Hg.): Proceedings of the European Conference on Heat Treatment 2015 & 22nd IFHTSE Congress, 20.-22.05.2015, Venice, Italy

Wulff, D.; Holländer, U.; Lützenkirchen-Hecht, D.; Wagner, R.; Yilkiran, D.; Behrens, B.-A.; Maier, H. J. (2015): Characterisation of selective oxidised steel surfaces by GIXRD, In: Sternemann, C.; Wagner, R.; Lützenkirchen-Hecht, D. (Hrsg.): 11th DELTA User Meeting & Annual Report 2015, 2015; S. 70-71

Klaas, D.; Wienecke, A.; Wurz, M. C.; Rissing, L.; Freytag, P.; Maier, H. J. (2015): Smart System Integration: Moulding of Magnetic Field Sensors into AlSi9Cu3(Fe)-Alloys, In: SMTA, Pan Pacific Symposium Conference Proceedings, 2015.

Holländer, U.; Frank, J.; Möhwald, K.; Maier, H. J. (2015): Entwicklung einer korrosions- und verschleißbeständigen Eisenbasisschicht, In: Wiche, H.; Wesling, V.; Teichmann, C. (Hrsg.): Tagungsband 1. Niedersächsisches Symposium Materialtechnik, 12. bis 13. Februar 2015. Shaker, Herzogenrath, 2015, S. 101-112

Maier, H. J.; Behrens, B. A.; Wolf, L.; Moritz, J.; Neumann, A.; Diekamp, M.; Gretzki, T.; Rodman, D.; Schrödter, J.; Spiekermeier, S.; Hübner, S.; Nürnberger, F. (2015): Formhärten und Spraykühlung – Potenziale und Anwendungsmöglichkeiten, In: Merklein, M. (Hrsg.): 10. Erlanger Workshop Warmblechumformung 2015. Meisenbach GmbH-Verlag, Bamberg, 2015, S. 59-78

Reimche, W.; Bruchwald, O.; Frackowiak, W.; Maier, H. J. (2015): Hochleistungsbauteile für den Leichtbau mit sensorkontrollierter Bainitumwandlung aus der Schmiedewärme, In: Borsutzki, M. (Hrsg.): Fortschritte in der Werkstoffprüfung für Forschung und Praxis. Verl. Stahleisen, Düsseldorf, 2015, S. 221-228

Nicolaus, M.; Möhwald, K.; Maier, H. J.  (2015): Development of a two-stage hybrid Technology for repairing Turbine Blades, In: ASM International (Hrsg.): Thermal Spray 2015. Proceedings from the International Thermal Spray Conference and Exposition. ASM International, Materials Park, Ohio, 2015; S. 37-40

Nicolaus, M.; Rottwinkel, B.; Möhwald, K.; Nölke, C.; Kaierle, S.; Maier, H. J.; Wesling, V.  (2015): Future regeneration processes for high pressure turbine blades, Deutscher Luft- und Raumfahrtkongress, Rostock, 22.09.-24.09.2015

Hildenbrand, P.; Sieczkarek, P.; Matthias, S.; Löffler, M.; Besserer, H.-B.; Merklein, M.; Tekkaya, A. E.; Reithmeier, E.; Maier, H. J. (2015): Inkrementelles Umformen dünnwandiger Funktionsbauteile unter Einsatz prozessangepasster Halbzeuge durch Verfahren der Blechmassivumformung, Tekkaya, A. E.; Liewald, M.; Merklein, M.; Behrens, B.-A. (Hg.): Tagungsband zum 18. Workshop Simulation in der Umformtechnik & 3. Industriekolloquium Blechmassivumformung 2015 - DFG Transregio 73, Dortmund, 26. - 27. Februar. Aachen: Shaker Verlag, S. 149-170

Zeller, S.; Beese, S.; Gerstein, G.; Isik, K.; Löhnert, S.; Nürnberger, F.; Wriggers, P.; Maier, H. J.; Tekkaya, A. E. (2015): Möglichkeiten der simulativen Vorhersage von Temperaturentwicklung und Bauteilversagen infolge plastischer Deformation bei DP600 Bauteilen, Tekkaya, A. E.; Liewald, M.; Merklein, M.; Behrens, B.-A. (Hg.): Tagungsband zum 18. Workshop Simulation in der Umformtechnik & 3. Industriekolloquium Blechmassivumformung 2015 - DFG Transregio 73, Dortmund, 26. - 27. Februar. Aachen: Shaker Verlag, S. 113–128

Beiträge in Büchern

Weidling, M.; Besdo, S.; Schilling, T.; Bauer, M.; Hassel, T.; Bach, F.-W.; Maier, H. J.; Lamon, J.; Haverich, A.; Wriggers, P. (2015): Development of Magnesium Alloy Scaffolds to Support Biological Myocardial Grafts: A Finite Element Investigation, Lenarz, T.; Wriggers, P. (Hg.): Biomedical Technology, Publishing Lecture Notes in Applied and Computational Mechanics 74, Springer International Publishing, Switzerland, S. 81-100
DOI: 10.1007/978-3-319-10981-7_6

Zeitschriften/Aufsätze

Bal, B.; Gumus, B.; Gerstein, G.; Canadinc, D.; Maier, H.J. (2015): On the micro-deformation mechanisms active in high-manganese austenitic steels under impact loading, Materials Science and Engineering: A, 632; 29-34
DOI: 10.1016/j.msea.2015.02.054

Gumus, B.; Bal, B.; Gerstein, G.; Canadinc, D.; Maier, H. J.; Guner, F.; Elmadagli, M. (2015): Twinning activities in high-Mn austenitic steels under high-velocity compressive loading, Materials Science and Engineering: A 648; 104-112.
DOI: dx.doi.org/10.1016/j.msea.2015.09.045

Wulff, D.; Yilkiran, D.; Holländer, U.; Lützenkirchen-Hecht, D.; Wagner, R.; Hübner, S.; Möhwald, K.; Maier, H. J.; Behrens, B.-A. (2015): Selective oxidation of 1.2379 tool steel surfaces: an approach for Dry Metal Forming, Dry Met. Forming OAJ FMT 1, 2015, 72-78

Hassel, T.; Klett, J.; Kunde, C.; Leuterer, R.; Maier, H. J.; Stuhr, J. (2015): Kraftschlüssiger Spaltausgleich an imperfekten Flanschverbindungen, Schiff und Hafen 10, 2015; 40-42.

Klett, J.; Hassel, T.; Maier, H. J.; Kunde, C.; Leuterer, R.; Stuhr, J. (2015): Friction-locked gap compensation in imperfect flange connections, Ship & Offshore 6, 2015, 36 - 38.

Panchenko, E. Yu; Chumlyakov, Yu I.; Surikov, N. Yu; Maier, H. J.; Gerstein, G.; Sehitoglu, H. (2015): Superelasticity in high-strength heterophase single crystals of Ni51.0Ti36.5Hf12.5 alloy, Technical Physics Letters 41 (8), 2015; 797-800.
DOI: 10.1134/S1063785015080283

Schmidt. H. S.; Ebbert, C.; Rodman, D.; Homberg, W.; Grundmeier, G.; Maier, H. J. (2015): Investigation of cold pressure welding: cohesion coefficient of copper, Key Engineering Materials 651-653 (2015), S. 1421-1426
DOI: 10.4028/www.scientific.net/KEM.651-653.1421

Nicolaus, M.; Möhwald, K.; Maier, H. J. (2015): Combined brazing and alitising process for thermally sprayed Ni-based alloys for the repair of turbine blades, Thermal Spray Bulletin, 2015, 8; S. 56-61.

Durisin, M.; Seitz, J. M.; Reifenrath, J.; Weber, C. M.; Eifler, R.; Maier, H. J.; Lenarz, T.; Klose, C. (2015): A novel biodegradable frontal sinus stent (MgNd2): a long-term animal study, European Archives of Oto-Rhino-Laryngology
DOI: 10.1007/s00405-015-3774-7

Durisin, M.; Reifenrath, J.; Weber, C. M.; Eifler, R.; Maier, H. J.; Lenarz, T.; Seitz, J.-M. (2015): Biodegradable nasal stents (MgF 2 -coated Mg-2 wt %Nd alloy)-A long-term in vivo study, Journal of Biomedical Materials Research Part B: Applied Biomaterials
DOI: 10.1002/jbm.b.33559

Knödler, P.; Otten, M.; Möhwald, K.; Maier, H. J.; Freiburg, D.; Peuker, A.; Biermann, D. (2015): Transplantation von thermisch gespritzten Schichten, Thermal Spray Bulletin 8, 2015 (1), 50-55.

Kokorin, V. V.; Konoplyuk, S. M.; Dalinger, A.; Thürer, S.; Gerstein, G.; Maier, H. J. (2015): Stress-induced resistivity changes in a Ni-Mn-In alloy, Applied Physics Letters, 2015, 106; 131908.
DOI: 10.1063/1.4917016

Vollmer, M.; Krooß, P.; Segel, C.; Weidner, A.; Paulsen, A.; Frenzel, J.; Schaper, M.; Eggeler, G.; Maier, H. J.; Niendorf, T. (2015): Damage Evolution in Pseudoelastic Polycrystalline Co-Ni-Ga High-temperature Shape Memory Alloys, Journal of Alloys and Compounds 633, 2015; 288-295.
DOI: 10.1016/j.jallcom.2015.01.282

Bruchwald, O.; Frackowiak, W.; Reimche, W.; Maier, H. J. (2015): Non-destructive in situ monitoring of the microstructural development in high performance steel components during heat treatment, La Metallurgia Italiana - International Journal of the Italian Association for Metallurgy 2015 (11/12), 29-37

Almohallami, A.; Yilkiran, D.; Wulff, D.; Hübner, S.; Vucetic, M.; Maier, H. J.; Behrens, B.-A.  (2015): Numerical Modelling of the Tribology of a Selective Oxidised 1.2379 Tool Steel Surface Developed for Dry Metal Forming , Dry Met. Forming OAJ FMT 1, 2015; 91-95

Niendorf, T.; Krooß, P.; Somsen, C.; Rynko, R.; Paulsen, A.; Batyrshina, E.; Frenzel, J.; Eggeler, G.; Maier, H. J. (2015): Cyclic degradation of titanium–tantalum high-temperature shape memory alloys — the role of dislocation activity and chemical decomposition, Functional Materials Letters 8, 2015; S. 1550062-1 - 1550062-5
DOI: 10.1142/S1793604715500629

T. Niendorf, F. Brenne, P. Hoyer, D. Schwarze, M. Schaper, R. Grothe, M. Wiesener, G. Grundmeier, H.J. Maier (2015): Processing of New Materials by Additive Manufacturing: Iron-Based Alloys Containing Silver for Biomedical Applications, Metall. Mater. Trans. A 46, 2015; S. 2829-2833
DOI: 10.1007/s11661-015-2932-2

Bruchwald, O.; Frackowiak, W.; Bucquet, T.; Huskic, A.; Reimche, W.; Maier, H. J. (2015): In-situ-Erfassung der Werkstoffumwandlung und Gefügeausbildung von Schmiedebauteilen im Abkühlpfad, HTM Journal of Heat Treatment and Materials 70 (3), 2015; S. 150-161
DOI: 10.3139/105.110259

Kadletz, P. M.; Krooß, P.; Chumlyakov, Y. I.; Gutmann, M. J.; Schmahl, W. W.; Maier, H. J.; Niendorf, T. (2015): Martensite stabilization in shape memory alloys – Experimental evidence for short-range ordering, Materials Letters 159, 2015; S. 16-19.
DOI: 10.1016/j.matlet.2015.06.048

Holländer, U.; Weber, F.; Möhwald, K.; Maier, H. J. (2015): Determination of failure criteria of mechanically and corrosively loaded brazed joints of sheets made of stainless chromium-nickel steel, Welding and Cutting, 14, 2015 (5), 280-288

Holländer, U.; Weber, F.; Möhwald, K.; Maier, H. J. (2015): Ermittlung von Versagenskriterien mechanisch-korrosiv belasteter Hartlötverbindungen von Blechen aus hochlegiertem nitchtrostendem Chrom-Nickel-Stahl, Schweißen und Schneiden, 67, 2015 (4), 174-182

Timofeeva, E. E.; Panchenko, E. Y.; Chumlyakov, Y. I.; Vetoshkina, N. G.; Maier, H. J. (2015): One-way and two-way shape memory effect in ferromagnetic NiFeGaCo single crystals, Materials Science and Engineering: A 640, 2015; 465-470
DOI: 10.1016/j.msea.2015.06.024

Gontarenko, A.; Möhwald, K.; Deißer, T. A.; Maier, H. J. (2015): Dry Sliding Wear Behavior and Wear Mechanisms of Thermally Sprayed WCCo-Coatings, Applied Mechanics and Materials 788, 2015, 143-150
DOI: 10.4028/www.scientific.net/AMM.788.143

Kiliclar, Y.; Vladimirov, I. N.; Wulfinghoff, S.; Reese, S.; Demir, O. K.; Weddeling, C.; Tekkaya, A. E.; Engelhardt, M.; Klose, C.; Maier, H. J. (2015): Finite element analysis of combined forming processes by means of rate dependent ductile damage modelling, International Journal of Material Forming, 2015
DOI: 10.1007/s12289-015-1278-z

Karaca, H. E.; Acar, E.; Ded, G. S.; Saghaian, S. M.; Basaran, B.; Tobe, H.; Kok, M.; Maier, H.J.; Noebe, R. D.; Chumlyakov, Y. I. (2015): Microstructure and transformation related behaviors of a Ni45.3Ti29.7Hf20Cu5 high temperature shape memory alloy, Materials Science and Engineering: A 627, S. 82–94
DOI: 10.1016/j.msea.2014.12.111

Hübsch, C.; Dellinger, P.; Maier, H. J.; Stemme, F.; Bruns, M.; Stiesch, M.; Borchers, L. (2015): Protection of yttria-stabilized zirconia for dental applications by oxidic PVD coating, Acta Biomaterialia 11, S. 488–493
DOI: 10.1016/j.actbio.2014.09.042

Krooß, P.; Niendorf, T.; Kadletz, P. M.; Somsen, C.; Gutmann, M. J.; Chumlyakov, Y. I.; Schmahl, W. W.; Eggeler, G.; Maier, H. J. (2015): Functional Fatigue and Tension–Compression Asymmetry in [001]-Oriented Co49Ni21Ga30 High-Temperature Shape Memory Alloy Single Crystals, Shape Memory and Superelasticity 1 (1), 2015; 6-17.
DOI: 10.1007/s40830-015-0003-6

Chowdhury, P.; Sehitoglu, H.; Abuzaid, W.; Maier, H. J. (2015): Mechanical response of low stacking fault energy Co–Ni alloys – Continuum, mesoscopic and atomic level treatments, International Journal of Plasticity 71, 2015; 32-61

Niendorf, T.; Krooß, P.; Somsen, C.; Eggeler, G.; Chumlyakov, Y. I.; Maier, H. J. (2015): Martensite aging – Avenue to new high temperature shape memory alloys, Acta Materialia 89, S. 298-304
DOI: 10.1016/j.actamat.2015.01.042

Weber, C. M.; Eifler, R.; Seitz, J.-M.; Maier, H. J.; Reifenrath, J.; Lenarz, T.; Durisin, M. (2015): Biocompatibility of MgF2-coated MgNd2 specimens in contact with mucosa of the nasal sinus – A long term study, Acta Biomaterialia 18, 2015; 249-261
DOI: 10.1016/j.actbio.2015.03.003

Vortrag

Aldag, D.; Varahram, A.; Lehr, J.; Maier, H.; Hassel, T. (2015): Automated and Fast Expandable Casing Connection Method Utilizing MIAB-Welding Technology, Expandable Technology Forum (ETF). Hamburg, 03.06.2015

2014

Konferenz

Seitz, J-M.; Eifler, R.; Vaughan, M.; Seal, C.; Hyland, M.; Maier, H. J. (2014): Coating Systems for Biodegradable Magnesium Applications, Magnesium Technology 2014, TMS (The Minerals, Metals & Materials Society), Wiley Published by John Wiley & Sons, Inc., Hoboken, New Jersey. Published simultaneously in Canada, (2014), S. 371-374

Demminger, C.; Klose, C.; Taptimthon, P.; Maier, H. J. (2014): Material-inherent data storage using magnetic magnesium-cobalt alloys, Procedia Technology 5, 2nd International Conference of System-Integrated Intelligence: Challenges for Product and Production Engineering Bremen, 2.-04.07.2014, S. 188-197
DOI: 10.1016/j.protcy.2014.09.071

Nicolaus, M.; Möhwald, K.; Maier, H. J. (2014): Common application of Ni-based fillermetals and hotgascorrosion protection coatings by means of thermal spraying with subsequent heat treatment for near net shape turbineblade repairing, In: Bouzakis, K.-D. et al. (Hrsg.): Proceedings / 11th International Conference THE "A" Coatings in Manufacturing Engineering, 1 - 3 October 2014, Thessaloniki, Greece. Ed. Ziti, Thessaloniki, 2014, S. 179-184

Bucquet, T.; Gulpak, M.; Egorov, F.; Garbrecht, M.; Hoja, T.; Hoffmann, F.; Fritsching, U.; Brinksmeier, E; Zoch, H.-W.; Fischer, M.; Dickert, H. H.; Bleck, W; Labanova, N.; Hajyheydari, E.; Felde, A.; Liewald, M.; Huskic, A.; Kazhai, M.; Hadifi, T.; Bouguecha, A.; Behrens, B.-A; Reimche, W.; Bruchwald, O.; Frackowiak, W.; Maier, H. J. (2014): EcoForge - Prozessintegrierte Wärmebehandlung bainitischer Stähle , Behrens, B.-A. (Hg.): Tagungsband zum 21. Umformtechnisches Kolloquium Hannover, S. 245-264

Reimche, W.; Bruchwald, O.; Frackowiak, W.; Maier, H. J. (2014): Sensorkontrollierte Umwandlung aus der Schmiedewärme zur Prozesssteuerung und Bauteiloptimierung , Behrens, B.-A. (Hg.): Tagungsband zum 21. Umformtechnisches Kolloquium Hannover, S. 338

Freiburg, D.; Biermann, D.; Peuker, A.; Kersting, P.; Maier, H. J.; Möhwald, K.; Knödler, P.; Otten, M. (2014): Development and Analysis of Microstructures for the Transplantation of Thermally Sprayed Coatings, Procedia CIRP Vol. 14, 6th CIRP International Conference on High Performance Cutting, HPC2014, S. 245 -250
DOI: 10.1016/j.procir.2014.03.054

Zaremba, D.; Wachsmuth, S.; Schneider, P.; Hufenbach, W.; Maier, H. J.; Hassel, T. (2014): Method for the material-specific repair preparation of carbon fiber reinforced plastic structures, Proceedings of the 22nd International Conference on Water Jetting, Haarlem, Netherlands, 3-5 September 2014, pp. 45-56.

Bauer, M.; Eiben, F.; Bach, Fr.-W.; Maier, H. J.; Hassel, T. (2014): New valve technology for AWSJ cutting, Proceedings of the 22nd International Conference on Water Jetting, Haarlem, Netherlands, 3-5 September 2014, pp. 99-106

Hassel, T.; Bauer, M.; Hoyer, P.; Patil, A. J.; Beniash, E.; Bach, F.-W.; Maier, H. J.  (2014): Study of magnesium fluoride and self-assembled organosilane coatings of AZ31 and MgCa0.8 alloys, 6th Symposium on Biodegradable Metals, University Politecnico di Milano, Maratea, Italien, 24.-29. August 2014

Durisin, M.; Lenarz, T.; Kanaan, N.; Bach, F.-W.; Angrisani, G. L.; Maier, H. J. (2014): Changes on a platinum electrode surface during acoustic stimulation of a cochlear implant – in vitro approach, 48. Jahrestagung der deutschen Gesellschaft für Biomedizinische Technik (DGBMT), Hannover, 8.-10.10.2014, Biomedical Engineering/Biomedizinische Technik 59 (S1), S. 1144–1147
DOI: 10.1515/bmt-2014-5014

Eifler, R.; Seitz, J. M.; Klose, C.; Bach, F.-W. (2014): Drawing and Stranding of Magnesium Wires for use as a Resorbable Suture Material, 48. Jahrestagung der deutschen Gesellschaft für Biomedizinische Technik (DGBMT), Hannover, 8.-10.10.2014, Biomedical Engineering/Biomedizinische Technik 59 (S1), S.1186
DOI: 10.1515/bmt-2014-5014

Durisin, M.; Weber, C. M.; Reifenrath, J.; Kietzmann, M.; Seitz, J. M.; Eifler, R.; Maier, H. J.; Lenarz, T. (2014): In vivo study of a biodegradable nasal stent (MgF2-coated MgNd2 alloy) in a minipig for up to six months, 48. Jahrestagung der deutschen Gesellschaft für Biomedizinische Technik (DGBMT), Hannover, 8.-10.10.2014, Biomedical Engineering/Biomedizinische Technik 59 (S1), S.1203
DOI: 10.1515/bmt-2014-5014

Durisin, M.; Weber, C. M.; Angrisani, N.; Seitz, J. M.; Eifler, R.; Maier, H. J.; Lenarz, T. (2014): Biocompatibility of MgF2-coated MgNd2 alloys in contact with nasal mucosal tissue – in vivo approach, 48. Jahrestagung der deutschen Gesellschaft für Biomedizinische Technik (DGBMT), Hannover, 8.-10.10.2014, Biomedical Engineering/Biomedizinische Technik 59 (S1), S.108
DOI: 10.1515/bmt-2014-5000

Böhm, V.; Maier, H. J.; Bach, F.-W.; Reimche, W.; Behrens, B.-A.; Odening, D.  (2014): Acoustic process monitoring during transient precision forging of high strengh components, Ludger Overmeyer und Vyacheslav P. Shkodyrev (Hg.): AST - Symposium on Automated Systems and Technologies. Proceedings, Hannover, 15-16 October 2014. 1. Aufl. Garbsen: TEWISS (Berichte aus dem ITA, 2014, Bd. 4), S. 105–110

Grittner, N.; Engelhardt, M.; Neumann, A.; Klose, C.; Hübner, S.; Behrens, B.-A.; Maier, H. J. (2014): A novel process for producing large scale Mg-sheets, Magnesium Technology 2014, TMS (The Minerals, Metals & Materials Society), Wiley Published by John Wiley & Sons, Inc., Hoboken, New Jersey. Published simultaneously in Canada, (2014), S. 289-292

Weidling, M.; Besdo, S.; Schilling, T.; Bauer, M.; Hassel, T.; Bach, Fr.-W.; Maier, H. J.; Haverich, A.; Wriggers, P. (2014): Finite element simulations for development of cardiovascular implants to support biological grafts, 48. Jahrestagung der deutschen Gesellschaft für Biomedizinische Technik (DGBMT), Hannover, 8.-10.10.2014, Biomedical Engineering/Biomedizinische Technik 59 (S1), S.984
DOI: 10.1515/bmt-2014-4422

Bauer, M.; Hassel, T.; Grünzel, O.; Hinz, C.; Schilling, T.; Kaufeld, K. T.; Bach, Fr.-W.; Maier, H. J.; Haverich, A. (2014): Characterization of native and decellularised aortic tissue by using uniaxial tensile test, 48. Jahrestagung der deutschen Gesellschaft für Biomedizinische Technik (DGBMT), Hannover, 8.-10.10.2014, Biomedical Engineering/Biomedizinische Technik 59 (S1), S.115
DOI: 10.1515/bmt-2014-4509

Holländer, U.; Weber, F.; Möhwald, K.; Maier, H. J. (2014): Entwicklung und Test eines Prüfverfahrens zur Bewertung von Lötverbindungen bei kombinierter mechanisch-korrosiver Belastung, Tagungsband zum 17. Werkstofftechnischen Kolloquium in Chemnitz, Schriftenreihe Werkstoffe und werkstofftechnische Anwendungen (52), Eigenverlag Chemnitz, S. 164-171

Beiträge in Büchern

Bach, Fr.-W.; Möhwald, K.; Erne, M.; Hübsch, C.; Maier, H. J. (2014): Microstructured thermally sprayed surfaces, B. Denkena, A. Rienäcker, G. Knoll, F.-W. Bach, H. J. Maier, E. Reithmeier und F. Dinkelacker (Hg.): Microstructuring of thermo-mechanically highly stressed surfaces. Final report of the DFG Research Group 576, Springer-Verlag, Heidelberg New York Dordrecht London, S. 58–92

Zeitschriften/Aufsätze

Toker, S. M; Canadinc, D.; Taube, A.; Gerstein, G.; Maier, H. J. (2014): On the Role of Slip - Twin Interactions on the Impact Behavior of High-Manganese Austenitic Steels, Mater. Sci. Eng. A., vol. 593, 120–126.

Krooß, P.; Holzweissig, M. J.; Niendorf, T.; Somsen, C.; Schaper, M.; Chumlyakov, Y. I.; Maier H. J. (2014): Thermal Cycling Behavior of an Aged FeNiCoAlTa Single-crystal Shape Memory Alloy, Scripta Materialia (81), S. 28–31
DOI: 10.1016/j.scriptamat.2014.02.020

Kokorin, V. V.; Koledov, V. V.; Shavrov, V. G.; Konoplyuk, S. M.; Thürer, S.; Troyanovsky, D. A.; Maier, H. J.; Khovaylo, V. V. (2014): Effect of thermal cycling on the martensitic transformation in Ni-Mn-In alloys, Journal of Applied Physics, 116; S. 103515
DOI: 10.1063/1.4895585

Holzweissig, M. J.; Kanagarajah, P.; Maier, H. J. (2014): Digital image correlation at high temperatures for fatigue and phase transformation studies, The Journal of Strain Analysis for Engineering Design (49), S. 204-211
DOI: 10.1177/0309324713498737

Batyrshina, E.; Maier, H. J. (2014): Metalle, die sich erinnern: Mit Formgedächtnis immer in der richtigen Fassung, Unimagazin 01/02 2014, S. 30-33

Biermann, D.; Kirschner, M.; Maier, H. J.; Bach, F.-W.; Möhwald, K.; Schaup, J. (2014): Active brazed ceramic cemented carbide compound drills for machining lamellar graphite cast iron, Prod. Eng. Res. Devel. (Production Engineering), 2014, vol. 8, 3
DOI: 10.1007/s11740-014-0547-x

Biermann, D.; Kirschner, M.; Maier, H. J.; Bach, F.-W.; Möhwald, K.; Schaup, J. (2014): Verbundbohrwerkzeug vereint Eigenschaftsvorteile der Fügepartner, Forum Schneidwerkzeug- und Schleiftechnik, Forum Schneidwerkzeug- und Schleiftechnik, 2014, 102-109

Ebbert, C.; Schmidt, H. C.; Rodman, D.; Nürnberger, F.; Homberg, W.; Maier, H. J.; Grundmeier, G. (2014): Joining with electrochemical support (ECUF): Cold pressure welding of copper, Journal of Materials Processing Technology, 2014, vol. 214, 2179–2187
DOI: http://dx.doi.org/10.1016/j.jmatprotec.2014.04.015

Ojha, A.; Sehitoglu, H.; Patriarca, L.; Maier, H. J. (2014): Twin Migration in Fe-based BCC Crystals: Theory and Experiments, Philosophical Magazine, 2014, vol. 94:16, 1816-1840
DOI: http://dx.doi.org/10.1080/14786435.2014.898123

Schmidt, H. C.; Rodman, D.; Grydin, O.; Ebbert, C.; Homberg, W.; Maier, H. J.; Grundmeier, G. (2014): Joining with electrochemical support: cold pressure welding of copper – weld formation and characterization, Advanced Materials Research, 2014, vol. 966-967, 453-460
DOI: 10.4028/www.scientific.net/AMR.966-967.453

Lützenkirchen-Hecht, D.; Wulff, D.; Wagner, R. ; Frahm, R.; Holländer, U.; Maier, H. J. (2014): Thermal anti-oxidation treatment of CrNi-steels as studied by EXAFS in reflection mode: the influence of monosilane additions in the gas atmosphere of a continuous annealing furnace, Journal of Material Science, 49, 2014, 5454-5461
DOI: 10.1007/s10853-014-8257-5

Niendorf, T.; Krooß, P.; Batyrsina, E.; Paulsen, A.; Frenzel, J.; Eggeler, G.; Maier, H. J. (2014): On the functional degradation of binary titanium–tantalum high-temperature shape memory alloys — A new concept for fatigue life extension, Funct. Mater. Lett.; 2014
DOI: 10.1142/S1793604714500428

P. Krooß, C. Somsen, T. Niendorf, M. Schaper, I. Karaman, Y. Chumlykov, G. Eggeler, H. J. Maier (2014): Cyclic Degradation Mechanisms in Aged FeNiCoAlTa Shape Memory Single Crystals, Acta Materialia 79, S. 126-137
DOI: http://dx.doi.org/10.1016/j.actamat.2014.06.019

Panchenko, E.; Chumlyakov, Y.; Eftifeeva, A.; Maier, H. J. (2014): Two-way Shape Memory Effect in Ferromagnetic Co₃₅Ni₃₅Al₃₀ Single Crystals Aged Under Stress, Scripta Materialia, 2014, Vol. 90-91, S. 10-13
DOI: 10.1016/j.scriptamat.2014.06.034

Mroz, G.; Reimche, W.; Frackowiak, W.; Bruchwald, O.; Maier, H. J.  (2014): Setting Discrete Yield-stress Sensors for Recording Early Component Loading Using Eddy-current Array Technology and Induction Thermography, Procedia Technology (15), S. 484–493
DOI: 10.1016/j.protcy.2014.09.008

Seitz, J-M; Eifler, R.; Weber, C.; Lenarz, T. H.; Maier, H. J.; Durisin, M. (2014): In vivo degradation effects of alloy MgNd2 in contact with mucous tissue, Journal of biomedical materials research. Part A.
DOI: 10.1002/jbm.a.35382

Dietrich, D.; Grittner, N.; Mehner, T.; Nickel, D.; Schaper, M.; Maier, H. J.; Lampke, T. (2014): Microstructural evolution in the bonding zones of co-extruded aluminium/titanium, J Mater Sci, 2014, vol. 49, 2442-2455
DOI: 10.1007/s10853-013-7912-6

Wulf, E.; Bachmann, H.; Möhwald, K.; Eifler, R.; Maier, H. J. (2014): The influence of brazing temperature and surface roughness on the wettability of reactive brazing alloys, IJMR (International Journal of Materials Research), 2014, vol. 105, 240-248
DOI: 10.3139/146.111022

Behrens, B.-A.; Maier, H. J.; Bach, F.-W.; Reimche, W.; Mroz, G.; Schrödter, J.; Jocker, J. (2014): A method to detect the level and direction of mechanical forces with the aid of load-induced martensitic phase transformation, Prod. Eng. Res. Devel., vol 8, 63-72

Ojha, A.; Sehitoglu, H.; Patriarca, L.; Maier, H. J. (2014): Twin Nucleation in Fe-based BCC Alloys - Modeling and Experiments, Modell. Sim. Mater. Sci. Eng., 22, S. 075010-1 - 075010-21
DOI: 10.1088/0965-0393/22/7/075010

Fischer, M.; Reimche, W.; Bruchwald, O.; Frackowiak, W.; Maier, H. J. (2014): EcoForge Energieeffiziente Prozesskette zur Herstellung von Hochleistungs-Schmiedebauteilen, HTM Journal of Heat Treatment and Materials, 69 (4), S. 209-219
DOI: 10.3139/105.110220

Bucquet T.; Reimche, W.; Bruchwald, O.; Frackowiak, W.; Maier, H. J. (2014): EcoForge – Ressourceneffiziente Prozessketten für Hochleistungsbauteile , Schmiede Journal (2), S. 22-27

Wang, J.; Sehitoglu, H.; Maier, H. J. (2014): Dislocation slip stress prediction in shape memory alloys, International Journal of Plasticity 54, S. 247–266
DOI: 10.1016/j.ijplas.2013.08.017

Astafurova, E. G.; Tukeeva, M. S.; Maier, G. G.; Melnikov, E. V.; Maier, H. J. (2014): Microstructure and mechanical response of single-crystalline high-manganese austenitic steels under high-pressure torsion: The effect of stacking-fault energy, Materials Science and Engineering A., (604), S. 166-175
DOI: 10.1016/j.msea.2014.03.029

Varahram, A.; Breidenstein, B.; Hassel, T.; Bach, F. -W; Maier, H. J. (2014): New design and construction of expandable casing tubes, Forschung im Ingenieurwesen 78 (3-4), S. 145-149

Niendorf, T.; Krooß, P.; Batyrsina, E.; Paulsen, A.; Motemani, Y.; Ludwig, A.; Buenconsejo, P.; Frenzel, J.; Eggeler, G.; Maier, H. J. (2014): Functional and structural fatigue of titanium tantalum high temperature shape memory alloys (HT SMAs), Materials Science and Engineering: A (620), S. 359-366
DOI: 10.1016/j.msea.2014.10.038

2013

Konferenz

Dellinger, P.; Möhwald, K.; Maier, H. J.; Bach, Fr.-W. (2013): Nano and Micro Structuring of PVD Surfaces by Using the Thin Film Transplantation Technology, 9th Asian-European International Conference on Plasma Surface Engineering (AEPSE 2013), Jejo (Korea), 25-30.08.2013

Freytag, P.; Kerber, K.; Maier, H. J. (2013): Nutzung von Beschichtungen aus Zinklegierungen zur Steigerung der Wärmeleitfähigkeit beim Verbundguss von Kupfer und Aluminium im Druckgussprozess, In: Verbundwerkstoffe. 19. Symposium Verbundwerkstoffe und Werkstoffverbunde (A. Wanner und K. A. Weidemann (Hg.)), Karlsruher Institut für Technologie (KIT), 2013, S. 9

Otten, M.; Möhwald, K.; Kerber, K.; Erne, M.; Knödler, P.; Maier, H. J.; Biermann, D.; Zabel, A.; Peuker, A. (2013): Untersuchung der mikro- und makroskopischen Abbildungsgenauigkeit von im Schichttransplantationsprozess übertragenden Oberflächenbeschichtungen, In: Verbundwerkstoffe. 19. Symposium Verbundwerkstoffe und Werkstoffverbunde (A. Wanner und K. A. Weidemann (Hg.)), Karlsruher Institut für Technologie (KIT), 2013, S. 10

Langohr A.; Swider M.A; Möller F.; Wulf E.; Möhwald K.; Hassel T.; Maier H. J. (2013): Development of flux free filler metals and processes for brazing of aluminum, In: Brazing, high temperature brazing and diffusion bonding. LÖT 2013, lectures and posters of the 10th international conference taking place in Aachen on 18th to 20th June 2013. Als Ms. gedr. Düsseldorf: DVS Media (DVS-Berichte, 293), 2013, S. 205–211

Liewald, M.; Hajyheydari, E.; Felde, A.; Fritsching, U.; Hinrichs, B.; Bucquet, T.; Fischer, M.; Dickert, H.; Bleck, W.; Behrens, B.-A.;Bouguecha, A.; Hadifi, T.; Huskic, A.; Kazhai, M.; Egorov, F.; Brinksmeier, E.; Maier, H.J.; Reimche, W.; Bruchwald, O.; Frackowiak, W. (2013): EcoForge – Resource-efficient process chains for high-performance components, Liewald (Hg.): Tagungsband Neuere Entwicklungen in der Massivumformung, Fellbach, 4. - 5.6.2013, S. 117–147

Frąckowiak, W.; Bruchwald, O.; Reimche, W.; Bach, F.-W.; Maier, H. J.  (2013): High Frequency Eddy-Current and Induction Thermography Inspection Techniques for Turbine Components, In: 18th International Workshop on Electromagnetic Non-destructive Evaluation (ENDE). Bratislava, SK, 25.-28.06.2013.

Reimche, W.; Bruchwald, O.; Frackowiak, W.; Bach, F.-W.; Maier, H. J. (2013): Sensorkontrollierte Umwandlung von Hochleistungsbauteilen aus der Schmiedewärme, In: Christ, H.-J. (Hrsg.): Tagung Werkstoffprüfung – Fortschritte in der Werkstoffprüfung für Forschung und Praxis, 28.11.-29.11. 2013, Neu-Ulm, S. 271-277

Knödler, P.; Peuker, A.; Erne, M.; Maier, H. J.; Möhwald, K.; Biermann, D.; Kerber, K.; Otten, M. (2013): Transfer of Micro-structures by Transplantation of Thermal Sprayed Coatings, In: Proceedings of the 10th International Conference THE “A“ Coatings (K.-D. Bouzakis, K. Bobzin, B. Denkena und M. Merklein (Hg.)), Shaker, Aachen, 2013, S. 193–204

Klose, C.; Demminger, C.; Maier, H. J.  (2013): Sensorische Werkstoffe - Erfassen und Nutzen mechanischer Beanspruchungsdaten im Lebenszyklus gentelligenter Bauteile, In: 8. Aachener Oberflächentechnik Kolloquium 2013. Herzogenrath (K. Bobzin (Hg.)), Shaker, 2013, S. 59–66

Klose, C.; Demminger, C.; Zwoch, S.; Reimche, W.; Bach, Fr.-W; Maier, H. J.; Kerber, K. (2013): Measurement of static and dynamic loads utilizing sensory magnesium components, In: Euro Intelligent Materials 2013 (E. Quandt und C. Selhuber-Unkel (Hg.)), DGM, 2013, S. 57

Verschiedenes

Meschut, G.; Hahn, O.; Matzke, M.; Olfermann, T.; Reimche, W.; B., Christoph; Mroz, G.; Bach, F.-W.; Maier, H. J.; Drossel, W.-G.; Neugebauer, R.; Ahnert, M.; Broschwitz, E.; Kraus, C. (2013): Lokale Konditionierung von presshartem Vergütungsstahl für das Hybridfügen von Mischbaustrukturen, Proceedings to conference 3 Fügetechnisches 2013

Zeitschriften/Aufsätze

Pataky, G.J; Sehitoglu, H.; Maier, H. J. (2013): Creep Deformation and Mechanisms in Haynes 230 at 800 °C and 900 °C, In: J Nuclear Materials 443, S. 484–490.

Kurtovic, A.; Brandl, E.; Mertens, T.; Maier, H. J. (2013): Laser Induced Surface Nano-structuring of Ti-6Al-4V for Adhesive Bonding, In: Int. J. Adhesion & Adhesives 45, S. 112–117.

Schmidt, H.C; Homberg, W.; Grundmeier, G.; Maier, H. J. (2013): Partial Joining of Blanks with Electrochemical Support (ECUF), In: Key Engineering Materials 554-557, S. 1091–1095.

Maier, G.G; Astafurova, E.G; Maier, H. J.; Naydenkin, E.V; Raab, G.I; Odessky, P.D; Dobatkin, S.V. (2013): Annealing Behavior of Ultrafine Grained Structure in Low-carbon Steel Produced by Equal Channel Angular Pressing, In: Mater. Sci. Eng. A 581, S. 104–107

Abuzaid, W.; Oral, A.; Sehitoglu, H.; Lambros, J.; Maier, H. J. (2013): Fatigue crack initiation in Hastelloy X - the role of boundaries, Fatigue & Fracture of Engineering Materials & Structures, 2013, 36 (8); 809-826.
DOI: 10.1111/ffe.12048

Patriarca, L.; Abuzaid, W.; Sehitoglu, H.; Maier, H. J. (2013): Slip transmission in bcc FeCr polycrystal, Materials Science & Engineering A, 588 (2013); 308–317.
DOI: 10.1016/j.msea.2013.08.050

Nicolaus, M.; Möhwald, K.; Bach, Fr.-W.; Maier, H. J. (2013): Wärmebehandlung thermisch gespritzter Ni-Basislote/NiCrAlY-Schichtsysteme zur Reparatur von Turbinenschaufeln, In: Thermal Spray Bulletin 6 (2), S. 119–123. Online verfügbar unter http://www.thermal-spray-bulletin.info/ index.cfm?objekt=TSPRAY& jahr=2013&ausgabe=2&rubrik=Wissenschaftliche%20Beitr%C3%A4ge.

Kanagarajah, P.; Brenne, F.; Niendorf, T.; Maier, H. J. (2013): Inconel 939 Processed by Selective Laser Melting: Effect of Microstructure and Temperature on the Mechanical Properties Under Static and Cyclic Loading, In: Materials Science and Engineering A 588, S. 188–195.

Karaca, H.E; Saghaian, S.M; Ded, G.; Tobe, H.; Basaran, B.; Maier, H. J.; Noebe, R.D; Chumlyakov, Y.I. (2013): Effects of Nanoprecipitation on the Shape Memory and Material Properties of an Ni-rich NiTiHf High Temperature Shape Memory Alloy, In: Acta Materialia 61, S. 7422–7431.

Chowdhury, P.B; Sehitoglu, H.; Rateick, R.G; Maier, H. J. (2013): Modeling Fatigue Crack Growth Resistance of Nanocrystalline Alloys, In: Acta Materialia 61, S. 2531–2547

Reimche, W.; Bruchwald, O.; Frackowiak, W.; Bach, Fr.-W.; Maier, H. J. (2013): Non-destructive determination of local damage and material condition in high-performance components, HTM (HTM Journal of Heat Treatment and Materials), S. 59-67
DOI: 10.3139/105.110176

Klose, C.; Demminger, C.; Mroz, G.; Reimche, W.; Bach, Fr.-W.; Maier, H. J.; Kerber K.  (2013): Influence of Cobalt on the Properties of Load-Sensitive Magnesium Alloys, In: Sensors 13, S. 106–118. Online verfügbar unter http://www.mdpi.com/1424-8220/13/1/106/.

Seitz, J.-M.; Eifler, R.; Bach, Fr.-W.; Maier H. J. (2013): Magnesium Degradation Products: Effects on Tissue and Human Metabolism, In: Journal of Biomedical Materials Research Part A. Online verfügbar unter http://onlinelibrary.wiley.com/doi/10.1002/jbm.a.35023/full.

2012

Konferenz

Birr, C.; Reimche, W.; Maier, H.J; Bach, Fr.-W.; Olfermann, T.; Matzke, M.; Meschut, G.; Hahn, O.; Ahnert, M.; Broschwitz, E.; Kraus, C.; Neugebauer, R. (2012): Lokale Konditionierung von presshartem Vergütungsstahl für das Hybridfügen von Mischbaustrukturen, In: FOSTA-EFB-DVS (Hg.): Gemeinsame Forschung in der Mechanischen Fügetechnik. 2. Fügetechnisches Gemeinschaftskolloquium 2012, S. 59–71.

Zeitschriften/Aufsätze

McMahon, R.E; Mab, J.; Verkhoturov, S.V; Munoz-Pinto, D.; Karaman, I.; Rubitschek, F.; Maier, H. J.; Hahn, M.S. (2012): A Comparative Study of the Cytotoxicity and Corrosion Resistance of Nickel--titanium and Titanium-niobium Shape Memory Alloys, In: Acta Biomaterialia 8, S. 2863–2870